Abstract:High-entropy alloy coatings (HECs) possess important prospects for tribological applications. In this research, CoCrFeNi, AlCoCrFeNi and MnCoCrFeNi-based HECs were prepared by subsonic flame spraying (SFS) process, which is an extremely convenient and very low-cost thermal spraying technology. The microstructure, phase composition, Vickers hardness, tribological behavior and wear mechanisms (as well as the effect of counterpart ball material, i.e., GCr15 bearing steel or Al2O3) of the HECs were studied under paraffin lubrication. The results indicated that the MnCoCrFeNi-based HEC had excellent tribological behaviors; the lowest friction coefficient (COF) (0.14) and wear rate (3.14 × 10–7 mm3 N−1 m−1) of the MnCoCrFeNi-based HEC were obtained with the GCr15 counterpart, where the dominant wear mechanisms were mild abrasive wear and tribo-oxidation wear. The combination of such factors as the higher oxide content, Vickers hardness and fracture toughness as well as the tribo-oxidation layer formed at the sliding interface significantly improved the wear resistance of the MnCoCrFeNi-based HEC sliding against GCr15 counterpart under micro-vibration reciprocating sliding mode. In contrast, the AlCoCrFeNi and CoCrFeNi-based HECs under the same sliding condition revealed much higher COF value and wear rate as well as quite distinct primary mechanisms of wear, i.e., abrasive, adhesive and tribo-oxidation wear for the AlCoCrFeNi-based HEC, adhesive wear with delamination for the CoCrFeNi-based HEC. When Al2O3 was utilized as counterpart, slight and typical abrasive wear occurred in the MnCoCrFeNi and AlCoCrFeNi-based HECs, respectively, while the primary wear mechanisms of the CoCrFeNi-based HEC changed to severe adhesive wear.

Microstructure and sliding wear behavior of HVOF sprayed Al(1−x)CoCrFeNiTix high-entropy alloy coatings

Microstructure, Mechanical Properties and High-Temperature Sliding Wear Response of a New Al0.5CrFeNiV0.5 High-Entropy Alloy

Microstructure and Wear Behavior of FeCoCrNiMo0.2 High Entropy Coatings Prepared by Air Plasma Spray and the High Velocity Oxy-Fuel Spray Processes

Microstructures and Wear Resistance of CoCrFeNi2V0.5Tix High-Entropy Alloy Coatings Prepared by Laser Cladding

Subsonic-Flame-Sprayed CoCrFeNi, AlCoCrFeNi and MnCoCrFeNi-Based High-Entropy Alloy Coatings and Their Tribological Behaviors

AlxCoCrFeNiSi high entropy alloy coatings with high microhardness and improved wear resistance

Sliding Wear of Spark Plasma Sintered CrFeCoNiCu High-Entropy Alloy Coatings: Effect of Aluminum Addition

Microstructure and tribological behaviors of FeCoCrNiMoSi<sub>x</sub> high-entropy alloy coatings prepared by laser cladding

Wear and high-temperature oxidation resistance of (AlCrFeTiV)100-xNix high-entropy alloy coatings prepared by laser cladding on Ti6Al4V alloy

Microstructural and Tribological Behavior of Thermal Spray CrMnFeCoNi High Entropy Alloy Coatings

Microstructure and properties of FeCoNiCrX (X=Mn, Al) high-entropy alloy coatings

Microstructure and Tribological Properties of FeCoCrNi High-Entropy Alloy Coatings Fabricated by Atmospheric Plasma Spraying

Microstructure Evolution and Properties of Laser Cladding CoCrFeNiTiAlx High-Entropy Alloy Coatings

Microstructural characteristics and enhanced wear resistance of nanoscale Al<sub>2</sub>O<sub>3</sub>/13 wt%TiO<sub>2</sub>-reinforced CoCrFeMnNi high entropy coatings

Microstructure and Mechanical Properties of FeCoCrNiNb(X )High-Entropy Alloy Coatings

Microstructure and high-temperature wear behavior of CoCrFeNiWx high-entropy alloy coatings fabricated by laser cladding

Mechanical properties and wear behaviors of FeCoNiCrMnTix high-entropy alloys manufactured by vacuum arc melting

Tribology behavior in laser cladded dual-phase Al x CoCrFeNiMn (1-x) high entropy alloys influenced by hierarchical interface architecture

Effect of Mo on microstructure and sliding wear performance of CoCrFeNiMox high entropy alloy coatings by laser cladding

Microstructure, thermostability and tribological behavior of composite CoCrFeNiTix high-entropy alloy coatings fabricated by laser cladding

Microstructure and tribological properties of Al2O3 reinforced FeCoNiCrMn high entropy alloy composite coatings by cold spray