Abstract:Evolutions of grain structure, texture and mechanical properties in ZK60 Mg alloy occasioned by bobbin tool FSW were measured.Dispersion and segregation of Zr-rich precipitates occurs in the stir zone (SZ), which results in evolution of a bimodal grain structure.Texture distribution of the BTFSW joint exhibited different characteristics with respect to that of the FSW joint.The overall variation trend of hardness of the joint exhibited weak grain size dependence.Texture distribution is the dominate factor affecting the fracture behavior of the BTFSW joint.ZK60B (Mg-6% Zn-0.6% Zr) alloy joints fabricated by bobbin tool friction stir welding (BTFSW) with various traverse speeds were investigated. The sound joint fabricated by the BTFSW was possible under the appropriate welding parameters. The severe plastic deformation during BTFSW resulted in dispersion and segregation of the Zr-rich particles within the stirred zone (SZ) followed by evolution of a bimodal grain structure with distributed bands of 0.8-1.7 μm ultrafine grains and 4.1-7.1 μm equiaxed grains. Micro-hardness of SZ is substantially reduced in contrast to that of parent metal (PM) in spite of the finer grain size owing to dissolution of Mg-Zn based precipitates having hardening effects on alpha-Mg matrix. With the decrease in traverse speed, randomization degree of the plasticized metal flow increases, which is evidenced by the randomized arc line pattern at the low traverse speed. Among all defect-free joints, the 200 mm/min joint exhibits the weakest isotropy of texture within SZ and the best tensile properties, which has reduced ultimate tensile strength and yield strength by 5.4% and by 22.2%, respectively, as compared to the PM. The randomized texture hinders the joint fracturing within SZ at low elongation. Therefore, a relatively high elongation of 10.8% was achieved, which corresponded to 72% of the PM value.

Revealing the microstructure characteristics, deformation behavior and mechanical properties of weakly textured Mg–Y-Nd-Gd-Zr alloy FSW joints

Microstructural Evolution and Mechanical Properties of Friction Stir Welded Mg–Zn–Y–Zr Alloy

Microstructure and Properties of Mg-Gd-Y-Zn-Mn High-Strength Alloy Welded by Friction Stir Welding

Microstructure and Mechanical Properties of Friction Stir-Welded Mg-2Nd-0.3Zn-0.4Zr Magnesium Alloy

Effect of Y Addition on Microstructure and Mechanical Properties of Friction Stir Welded Zk60 Alloy

Mechanical Response, Twinning Behaviours and Strain Incompatibility of FSWed-AZ31B Joints Along Different Loading Paths

Investigations on the material flow and the influence of the resulting texture on the tensile properties of dissimilar friction stir welded ZK60/Mg–Al–Sn–Zn joints

Effect of Self-Reacting Friction Stir Welding on Microstructure and Mechanical Properties of Mg-Al-Zn Alloy Joints

Improving microstructural and mechanical properties of dissimilar friction stir welded AZ61/AZ40 joint

Low-cycle fatigue behaviour of magnesium alloy thick plate joints fabricated via differential double-shoulder friction stir welding

Improving the mechanical properties of a friction stir welded AZ31 joint by adjusting the microstructure and texture

Microstructure and abnormal mechanical properties under the coupling effect of strain and temperature for friction-stir-welded joints of Al-Mg-Si alloy

Effect of microstructural evolution on mechanical properties of friction stir welded ZK60 alloy

Friction Stir Welding of Thick Plates of 4Y3Gd Mg Alloy: An Investigation of Microstructure and Mechanical Properties

Evolution of grain structure, texture and mechanical properties of a Mg–Zn–Zr alloy in bobbin friction stir welding

Effects of traverse speed on weld formation, microstructure and mechanical properties of ZK60 Mg alloy joint by bobbin tool friction stir welding

Microstructure and Mechanical Properties of Friction Stir-Welded Dissimilar Joints of ZK60 and Mg-4.6Al-1.2Sn-0.7Zn Alloys

Simultaneous Enhancement of Strength and Ductility in Friction Stir Welded AZ31 Alloy Via Multi-Pass Hot-Rolling and Subsequent Annealing

Microstructures and Mechanical Properties of Micro Friction Stir Welding (μfsw) of 6061-T4 Aluminum Alloy

Effect of Tool Offset and Tool Rotational Speed on Enhancing Mechanical Property of Al/Mg Dissimilar FSW Joints

Tensile Properties And Fracture Mechanism Of Friction Stir Weld On Az31 Magnesium Alloy