Abstract:O NE of the fundamental problems in restorative dentistry is the fabrication of cast gold appliances which accurately fit the cavity prepared in a tooth or the space between teeth located anywhere in the dental arches. Two important factors which must be considered in making such castings are the dimensional change of the wax pattern and the contraction or casting shrinkage of gold on cooling from the liquid state to room temperature. At the present time there are two widely used technics that compensate for these shrinkages. Both depend upon expansion of the casting investment. The older, more universal, technic, often referred to as the "thermal expansion" method, depends upon the presence in the investment of a material or materials which, when heated, will expand in a known manner to enlarge the mold. The more recently introduced method for increasing the mold size is based on the observation that some types of investment materials, when placed in water during the setting period, expand three to four times their normal setting expansion. The mechanism of this enlargement, commonly termed "hygroscopic expansion," will be discussed. The phenomenon of hygroscopic expansion was reported by Wilson' and was called to the attention of the dental profession by Scheu.2 Scheu's original observations on the expansion of setting inlay investment upon the addition of water are the basis for the present hygroscopic technic. Scheu noted that all investments expanded hygroscopically and that the amount of expansion depended upon the water-powder ratio and time of immersion. Scheu defined hygroscopic expansion as that expansion occurring when water comes in contact with a mass of setting investment. Numerous investigators3-6 have published the results of their findings following Scheu's original observations. Degni7 stated that the hygroscopic expansion was extremely sensitive to confinement of any kind. Degni also used the colloidal theory for the setting of plaster of Paris to explain the hygroscopic expansion process. Landgren8 presented an excellent report on some of the factors affecting hygroscopic expansion. Landgren noted that the water-powder ratio played an important role in determining the amount of expansion. He showed that the thicker the mix, the greater the amount of hygroscopic expansion. Landgren also showed that hygroscopic expansion decreases with an increase in time between spatulation and immersion when immersion is made after the initial set.

Fracture resistance of cement‐retained lithium disilicate implant‐supported crowns: Effect of material used for two‐piece abutments

Bridging silicon nanoparticles and thermoelectrics: phenylacetylene functionalization.

Restoration of Images Degraded by Motion Blur using Matrix Operators

Effect of abutment design on fracture resistance of resin-matrix ceramic crowns for dental implant restoration: an in vitro study

Fracture Resistance of Pressed and Milled Lithium Disilicate Anterior Complete Coverage Restorations Following Endodontic Access Preparation

Prevalence of hypercholesterolemia in a Kuwaiti Hospital outpatient population.

[Evaluation of the conductivity of a single calcium channel via the current fluctuations utilizing the EGTA effect].

Influence of occlusal thickness on the fracture resistance of chairside milled lithium disilicate posterior full‐coverage single‐unit prostheses containing virgilite: A comparative in vitro study

The Fracture Resistance of Additively Manufactured Monolithic Zirconia vs. Bi-Layered Alumina Toughened Zirconia Crowns When Cemented to Zirconia Abutments. Evaluating the Potential of 3D Printing of Ceramic Crowns: An In Vitro Study

Fracture behaviour of implant–implant- and implant–tooth-supported all-ceramic fixed dental prostheses utilising zirconium dioxide implant abutments

Influence of Different Thicknesses of Monolithic Crowns Made from Different Resin-Bonded Glass Ceramic on Their Load-bearing Capacity (An in vitro Comparative Study)

In vitro performance and fracture resistance of novel CAD/CAM ceramic molar crowns loaded on implants and human teeth

Fracture Strength of Endocrowns Fabricated From Three Different Computer-Aided Design/Computer-Aided Manufacturing Ceramic Materials: An In-Vitro Study

Fracture resistance of hybrid ceramic abutments with different restoration lengths: A pilot study

The Effect of Die Material on the Crown Fracture Strength of Zirconia Crowns

Influence of ceramic crown design (translucent monolithic zirconia vs. bilayered) of implant‐supported single crowns after mechanical cycling

Biomechanical behavior of different designs of hybrid abutment-restoration on the posterior crown: a finite element analysis

[Unclear neurological condition and fever].

Twentieth Annual Meeting

The Mechanism of Hygroscopic Expansion in Dental Casting Investments

Comparison of fatigue lifetime of new generation CAD/CAM crown materials on zirconia and titanium abutments in implant-supported crowns: a 3D finite element analysis