Abstract:This work aims at investigating the causes affecting the dimensional and geometrical accuracy of holes in metal binder jetting stainless steel parts. Parallelepiped samples with a through hole were produced using AISI 316L and 17-4PH powders, differing for diameter (3, 4, 5 mm), and position of the axes with respect to the building plane (6, 9, 12 mm distance). Dimensions and geometrical characteristics were measured at green and sintered state by a coordinate measuring machine, determining the dimensional change and the geometrical characteristics. As expected, the shrinkage of linear dimensions is anisotropic; moreover, change in volume and sintered density are significantly affected by the position in the printing chamber. Higher shrinkage was measured along building direction (Z) – 18.5 ÷ 19.5%, than in the building plane – 16.5 ÷ 17.5%, and slightly higher shrinkage – 0.5 ÷ 0.8% was measured along powder spreading direction (X) than binder injection direction (Y). A variation up to 3% in relative density of sintered parts depending on the position in the building plane was observed in 316L. The dimensional change of diameters generally confirmed the shrinkage predicted by the model previously developed—difference between real and expected dimensional changes lower than 3%, except for three geometries (4 ÷ 6%). The cylindricity form error of sintered parts was strongly underestimated by the prediction model (up to 0.15 mm), but underestimation was considerably reduced (generally lower than 0.05 mm) adding the cylindricity form error due to printing. Dimensional and geometrical accuracy of holes are strongly affected by shape distortion of the parallelepiped geometry, in turn due to layer shifting and inhomogeneous green density during printing, and to the effect of frictional forces with trays during sintering. Gravity load effect was also observed on the holes closest to the building plane. Future work will improve the reliability of the prediction model implementing the results of the present work.

Ex-situ characterization and simulation of density fluctuations evolution during sintering of binder jetted 316L

Effect of sintering temperature on binder jetting additively manufactured stainless steel 316L: densification, microstructure evolution and mechanical properties

In situ visualization of aluminum sintering for binder jetting by X-ray transmission

Influence of initial relative densities on the sintering behavior and mechanical behavior of 316 L stainless steel fabricated by binder jet 3D printing

Tailoring green and sintered density of pure iron parts using binder jetting additive manufacturing

Numerical simulation and experimental measurement of pressureless sintering of stainless steel part printed by Binder Jetting Additive Manufacturing

X-ray observation study of the influence of binder deposition on sintering process of aluminum binder jetting

A coupled thermo-mechanical material point model of binder jetted green part sintering

Influence of sintering processes on the density of nano-AgSnO2 composites

Effect of bimodal powder on densification and mechanical properties of 316L stainless steel fabricated by binder jet 3D printing

Exploring the sintering behavior of a complex ceramic powder system using in-situ X-ray nano-tomography

Densification and Properties of Bimodal 316L Stainless Steel Produced by Binder Jetting Printing with Addition of B4C

A printability evaluation of fine and coarse powder in binder jetting of dense and porous copper parts

Analysis of the causes determining dimensional and geometrical errors in 316L and 17-4PH stainless steel parts fabricated by metal binder jetting

Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals

Powder Optimization for Enhanced Printing and Sintering of Porous Tungsten in Binder Jet Printing

Microstructural Response of Highly Porous Sintered Nano-silver Particle Die Attachments to Thermomechanical Cycling

Experimental Study and X-Ray Microtomography Based Cfd Simulation for the Characterization of Pressure Drop in Sinter Bed

Effect of feedstock bimodal powder design and cold isostatic pressing on the mechanical behavior of binder jetting additive manufactured Inconel 718 superalloy

Mechanical and corrosion properties of full liquid phase sintered WE43 magnesium alloy specimens fabricated via binder jetting additive manufacturing

Investigation on the Attainment of High-Density 316L Stainless Steel with Selective Laser Sintering