Abstract:Ejector refrigeration systems pose a promising alternative to vapour compressor technologies. Still, they have not been penetrating the market because of the strong dependency of the ejector behaviour ("component-scale") on the underlying fluid-dynamics ("local-scale"), which directly affects the system performances ("system-scale"). Furthermore, within the broader discussion concerning refrigerant phase-out, the refrigerant selection is a cutting-edge and challenging task, especially because the ejector performance is influenced by the coupling taking place between the working fluid and component design. This paper contributes to the broader framework of ejector research investigating the complex relationships between the factors mentioned above that arise during the operation of a standard ejector refrigeration system. An integrated model (CFD-LPM) has been applied to compare fourth generation and natural refrigerants (R1233zd(E), R1234yf, R1234ze(E), R290, R1270, and R600a) to commonly used refrigerants (R134a, R245fa, R152a) on five ejector geometries, obtained changing the nozzle exit position and the mixing chamber throat dimension from a reference case. Based on the results in terms of performance curves, tested refrigerants could be divided into three groups: (i) R1270 and R290, having higher COP (0.5 – 1.03) but lower critical temperature Tcrit (20.7 – 25.0 °C), (ii) R134a, R152a, R1234yf, R1234ze R600a, with an intermediate value of COP (0.27 – 0.83) and critical temperature Tcrit (22.8 – 28.0 °C), (iii) R245fa and R1233zd, with lower COP (0.25 – 0.58) but higher critical temperature Tcrit (26.0 – 31.0 °C). Increasing nozzle exit position has been found to slightly affect the performances (+5% COP) while the ejector entrainment process has been found to highly depend on the mixing chamber diameter (up to +35% COP). One of the tested geometries has been then selected, with R290 as operative fluid, to perform a boundary conditions sensitivity analysis. This led to the definition of a system performance map for different system temperature levels at the generator and evaporator.

Simulation analysis on ejector performance with inclusion of chevrons in primary nozzle

An Investigation on the Component Efficiencies of a Small Two-Phase Ejector

Performance Study of an Enhanced Ejector Refrigeration Cycle with Flash Tank Economizer for Low-Grade Heat Utilization

Experimental investigation on two-phase driven ejector performance in a novel ejector enhanced refrigeration system

Performance enhancement of steam ejector via novel primary nozzle bypass: CFD analysis

The performance analysis of a variable geometry ejector utilizing CFD and artificial neural network

Analysis on the Optimal Mixing Pressure and Efficiency Limit of an Ideal Ejector

Improvement of the wet steam ejector performance in a refrigeration cycle via changing the ejector geometry by a novel EEC (Entropy generation, Entrainment ratio, and Coefficient of performance) method

Numerical Investigation on the Effect of Section Width on the Performance of Air Ejector with Rectangular Section

Conical-cylindrical mixer ejector design model for predicting optimal nozzle exit position

Numerical investigation in effects of refrigerants' thermodynamic properties on performance of supersonic ejector

Bypass ejector with an annular cavity in the nozzle wall to increase the entrainment: Experimental and numerical validation

Numerical Simulation on Two-Phase Ejector with Non-Condensable Gas

A Study on the Evolution Laws of Entrainment Performances Using Different Mixer Structures of Ejectors

Analysis of Refrigeration Cycle Performance with an Ejector

Effects of component geometries and inflow conditions on ejector operational mode

Multi-scale evaluation of ejector performances: The influence of refrigerants and ejector design

Numerical study of a CO 2 swirl ejector with lubricating oilEtude numérique d'un éjecteur tourbillonnant de CO 2 avec huile lubrifiante

Zeotropic mixture ejector: modeling approach, validation, and assessment based on composition ratio

Experimental study of the influence of nozzle and mixing chamber dimensions on the performance of the ejector

Experimental and numerical investigation of the effect of shock wave characteristics on the ejector performance