Abstract:Inductively coupled plasma generator is one of the core components of the near-space high-speed target plasma electromagnetic scientific experimental research device, which is often used to simulate high enthalpy and high speed plasma sheath environment. In order to study the discharge characteristics of inductively coupled plasma generator under high power, radio frequency and medium pressure, the numerical simulation and experiment are combined to study its internal heat transfer and flow characteristics in this paper. Based on the local thermodynamic equilibrium conditions, the numerical simulation of large-scale radio frequency and medium pressure inductively coupled plasma with a power of 100–400 kW is carried out through the multi-field coupling of flow, electromagnetic and temperature field, and verified by light intensity and spectrum experiment. The results show that the electromagnetic field distribution in the high-power thermal balance inductively coupled plasma generator is similar to that of the small- and medium-sized power plasma generator. The discharge energy dissipation occurs mainly in the area where the induction coil is located. The temperature of the inner wall of the quartz tube is higher at the coil location than in other areas, and the plasma has a ring-shaped high-temperature structure. The outer wall of the quartz tube is set to be the boundary condition of heat flux for simulating the temperature change of the quartz tube under cold blowing. This setting is in coincidence with factual situations. The wall temperature of the quartz tube at the entrance and at the induction coil section are found to be relatively high. When the large-size inductively coupled plasma generator works, an obvious return vortex is generated at the entrance due to the temperature difference and the electromagnetic pumping effect, and the exit velocity increases slightly with the increase of power. At the same time, the discharge experiment under the corresponding conditions shows that there is found a ring structure with bright edges and dark centers in the axial image of the argon discharge. Moreover, the emission spectrum of argon plasma is measured through the spectrum diagnosis system and the spatial distribution of the generator electron temperature is obtained. The light intensity of the discharge image and the electron temperature measured by the spectrum are found to be in comparative coincidence with the COMSOL simulation temperature result, demonstrating the validity of the numerical simulation results under thermodynamic equilibrium conditions. The numerical simulation results in this paper are also applicable to the optimization design and temperature resistance evaluation of the inductively coupled plasma generator.

Comparative Study of Collectors for High-Power Gridless Inductive Output Tube

Study of High-Power Gridless Inductive Output Tube with L-Shaped Cavity

Multipactor Analysis of 431 MHz L-shaped Inductive Output Tube Cavity

A Three-stage Depressed Collector for 220 GHz Sheet Beam Traveling-wave Tubes

Experiment and Power Capacity Investigation of Collector in the 50-kW-Average-Power $\textit{Q}$-Band Gyro-TWT

Study on Temperature Distribution and Response of Electron Collector in High-Power Microwave Generator

Study on a Depressed Collector for a 75 GHz Low-Voltage Compact Gyrotron for Industrial Application

Investigation of a Multi-Gap, High-Voltage Isolator for a Gyro-TWT With Depressed Collector

Heat Transfer Simulation and Analysis of Electron Collector Based on Real-time Uniformity Detection Device of Irradiation Accelerator

Study on a Cascade Pulse Tube Cooler with Work Recovery

A Multi-Stage Depressed Collector for 0.22 THz Sheet Beam Traveling-Wave Tubes

Modeling and Experiments on Fast Cooldown of A 120 Hz Pulse Tube Cryocooler

Influence of Hot End Heat Exchangers on Cascading Three Pulse Tube Coolers

Thermal-hydraulic Design of Collector Cooling for High Power Gyro-TWT

Numerical Simulation and Experimental Study of High-Power Thermal Equilibrium Inductively Coupled Plasma

Comprehensive design and whole-cavity simulation of a multi-beam inductive output tube using a 3rd harmonic drive on the grid

Experimental Investigation of a Q-Band Helix Traveling-Wave Tube with Four-Stage Depressed Collector

Comprehensive Design and Whole-Cavity Simulation of a Multibeam Inductive Output Tube Using a 3rd Harmonic Drive on the Grid

Design and Experiment of the Conventional Collector for W-band Gyrotron Oscillator

Collector Failures on 350 MHz, 1.2 MW CW Klystrons at the Low Energy Demonstration Accelerator (LEDA)

Optimization Method of High Efficiency Collector Based on Energy Distribution Measurement