Abstract:<p>Intermetallic γ ‐TiAl based alloys are a promising class of materials for lightweight high‐temperature applications. Following intensive research and development activities, they have recently entered service in the automotive and aircraft engine industries. In the course of the last decades, the development of these complex multi‐phase alloys has benefited considerably from the application of (in situ) X‐ray scattering and diffraction techniques. This review article seeks to provide a practical introduction and overview of recent progress in this field of research. In particular, four case studies taken from various stages in the alloy development (i.e. fundamental research – manufacturing, joining, and repair – and application) illustrate current prospects at modern synchrotron radiation sources, including detailed information on available setups for in situ high‐energy X‐ray diffraction and small‐angle X‐ray scattering experiments and a discussion of potential limitations in the use of these techniques.</p><p>This article is protected by copyright. All rights reserved.</p>

What problem does this paper attempt to address?

### Problems Addressed by the Paper The paper aims to explore the latest advancements in the structural changes, manufacturing, joining, and repair of γ-TiAl-based alloys, and to demonstrate the application of synchrotron X-ray techniques in such studies. Specifically, through four case studies, the paper details the application of these techniques and their potential limitations, covering different stages from fundamental research to practical applications. #### Summary of Main Content 1. **Material Properties and Applications**: - γ-TiAl-based alloys are widely used in aerospace and automotive engines due to their lightweight and high-temperature performance. - The development of techniques such as High-Energy X-ray Diffraction (HEXRD) and Small-Angle X-ray Scattering (SAXS) allows researchers to observe structural changes in materials under external forces or heat treatment conditions with high time resolution. 2. **Case Studies**: - Case Study I: An improved quenching dilatometer was used to study the two-step heat treatment process of a ternary Ti-44Al-7Mo (atomic percent) model alloy under different heating/cooling rates. - Case Study II: Time-resolved synchrotron X-ray diffraction experiments were demonstrated in laser beam welding experiments. - Case Study III: Various intermediate phases formed during the joining process of Nb-containing γ-TiAl-based alloys were discussed. - Case Study IV: The room temperature tensile behavior of TNM (Ti-43.5Al-4Nb-1Mo-0.1B) thin sheets was investigated. #### Research Methods - Synchrotron X-ray diffraction (HEXRD) and small-angle X-ray scattering (SAXS) techniques were used to study the microstructure of γ-TiAl-based alloys under different conditions. - A combination of various experimental setups, such as an improved quenching dilatometer and laser welding equipment, was used to obtain more comprehensive data. #### Target Audience - This review is aimed not only at the TiAl research community but also at other researchers in the field of materials science, especially those interested in experimental techniques and future developments. Through these case studies and technical introductions, the paper aims to provide new ideas and methods for the research and development of γ-TiAl-based alloys.

Exploring Structural Changes, Manufacturing, Joining, and Repair of Intermetallic γ‐TiAl‐Based Alloys: Recent Progress Enabled by In Situ Synchrotron X‐Ray Techniques

In Situ Characterization Techniques Based on Synchrotron Radiation and Neutrons Applied for the Development of an Engineering Intermetallic Titanium Aluminide Alloy

Recent Electron Microscopy Results on Micro- and Nanostructured Ni-Ti-(X) Shape Memory Alloys

Thermal Expansion of a Multiphase Intermetallic Ti-Al-Nb-Mo Alloy Studied by High-Energy X-ray Diffraction

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Design, Processing, Microstructure, Properties, and Applications of Advanced Intermetallic TiAl Alloys

Using transmission Kikuchi diffraction to characterise α variants in an α + β titanium alloy

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

In situ Imaging of Precipitate Formation in Additively Manufactured Al-Alloys by Scanning X-ray Fluorescence

Recent progress in the simulation of microstructure evolution in titanium alloys

Recent Advances in the Design of Novel Β‐titanium Alloys Using Integrated Theory, Computer Simulation, and Advanced Characterization

Development Status, Applications and Perspectives of Advanced Intermetallic Titanium Aluminides

Microstructure Design and Its Effect on Mechanical Properties in Gamma Titanium Aluminides

In Situ CT Tensile Testing of an Additively Manufactured and Heat-Treated Metastable ß-Titanium Alloy (Ti-5Al-5Mo-5V-3Cr)

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures

Topics on Microstructure Researches in TiAl Intermetallics Using Atomic Scale Observation and Computational Simulation

Structural Materials: Understanding Atomic-Scale Microstructures

Study of the Ti2al Phase and Gb Structures in Tial Intermetallics Using Atomic Scale Observation and Computational Simulation

Microstructures and micromechanical behaviors of high-entropy alloys investigated by synchrotron X-ray and neutron diffraction techniques: A review

High-energy synchrotron x-ray techniques for studying irradiated materials

Fabrication of γ-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties