Abstract:Direct ink writing (DIW) of aerogels has great potential in designing novel three-dimensional (3D) multifunctional materials with hierarchical structures ranging from the nanoscale to the macroscopic scale. In this paper, pure aerogels composed of inorganics, strongly cross-linking organics, and weakly cross-linking organics were directly written via the precise control of the gelation degree without using any additives. The rheological properties of a resorcinol–formaldehyde aerogel-based sol–gel ink (marked as RA ink) were measured at different reaction times to determine the suitable printable range (G′LVR: several 103 Pa) that ensures its good print fidelity. In addition, the rheological evolution of the RA ink during the sol–gel process and under different shear stresses was studied. The correlation of relevant parameters was established according to the Hagen–Poiseuille model. Other typical aerogel-based sol–gel inks including a silica aerogel-based sol–gel ink (SA ink) and a polyimide aerogel-based sol–gel ink (PA ink) for DIW were also demonstrated. Finally, water evaporation experiments were carried out using a 3D-printed carbonized resorcinol–formaldehyde aerogel (CA) to further exhibit the potential applications of this novel technology in solar steam generation. The evaporation rate (1.57 kg m–2 h–1) and efficiency (88.38%) of 3D-printed CA were higher than those of bulk CA (1.21 kg m–2 h–1 and 69.82%). This paper systematically studies the control of DIW parameters for aerogel-based sol–gel inks and shows a potential application in high-efficiency 3D-printed evaporators.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.langmuir.0c03312?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.langmuir.0c03312</a>.Rheological behaviors and thixotropic behaviors of RA inks (Figure S1); rheological behaviors of the SA ink and the PA ink (Figure S2); rapid solidification of the PA ink once it met water (Figure S3); Herschel–Buckley model for RA inks (Figure S4); study of relevant parameters in DIW (Figure S5); extrusion experiments for dextrin (Figure S6); extrusion experiments for RA inks (Figure S7); 3D-printed hydrogels using the RA ink, SA ink, and PA ink (Figure S8); TG-DSC tests for 3D-printed aerogels (Figure S9); uniaxial compression–decompression test for 3D-printed aerogels (Figure S10); derivation of the correlation of the relevant parameters; filament widths at varied applied pressures and writing speeds (Table S1); filament widths at varied heights of the needle to the substrate (Table S2); pressure value, maximum shear stresses, and yield stresses for dextrin and RA inks (Table S3); detailed parameters of bulk CA and 3D-printed CAs (Table S4); and water evaporation data of 3D-printed CAs, bulk CA, and pure water (Table S5).This article has not yet been cited by other publications.

3D-Printed Interfacially Jammed Emulsion Aerogels

Direct 3 D Printing of Ultralight Graphene Oxide Aerogel

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

3D Printing of Ultralow-Concentration 2D Nanomaterial Inks for Multifunctional Architectures

Direct Ink Write (DIW) 3D Printed Cellulose Nanocrystal Aerogel Structures

Direct ink writing of aloe vera/cellulose nanofibrils bio-hydrogels

Digital Light Processing 3D‐Printed Silica Aerogel and as a Versatile Host Framework for High‐Performance Functional Nanocomposites

Computational Study of Extrusion Bioprinting with Jammed Gelatin Microgel-Based Composite Ink

3D Printing of Bioactive Gel-like Double Emulsion into a Biocompatible Hierarchical Macroporous Self-Lubricating Scaffold for 3D Cell Culture

Versatile Direct Writing of Aerogel-Based Sol–Gel Inks

Depletion Flocculation of High Internal Phase Pickering Emulsion Inks: A Colloidal Engineering Approach to Develop 3D Printed Porous Scaffolds with Tunable Bioactive Delivery

3D Printing of Thermal Insulating Polyimide/Cellulose Nanocrystal Composite Aerogels with Low Dimensional Shrinkage

3D Printing of Graphene Aerogels.

Generalized 3D Printing of Graphene-Based Mixed-Dimensional Hybrid Aerogels

Cryo-Electrohydrodynamic Jetting of Aqueous Silk Fibroin Solutions

Additive-free graphene-based inks for 3D printing functional conductive aerogels

Direct ink writing of organic and carbon aerogels

A Journey from Structured Emulsion Templates to Multifunctional Aerogels

3D bioprinting of hydrogel/ceramic composites with hierarchical porosity

Depletion Attraction Driven Formation of Spirulina Emulsion Gels for 3D Printing

Extrusion-Based 3D Printing for Highly Porous Alginate Materials Production