Abstract:Direct ink writing (DIW) of aerogels has great potential in designing novel three-dimensional (3D) multifunctional materials with hierarchical structures ranging from the nanoscale to the macroscopic scale. In this paper, pure aerogels composed of inorganics, strongly cross-linking organics, and weakly cross-linking organics were directly written via the precise control of the gelation degree without using any additives. The rheological properties of a resorcinol–formaldehyde aerogel-based sol–gel ink (marked as RA ink) were measured at different reaction times to determine the suitable printable range (G′LVR: several 103 Pa) that ensures its good print fidelity. In addition, the rheological evolution of the RA ink during the sol–gel process and under different shear stresses was studied. The correlation of relevant parameters was established according to the Hagen–Poiseuille model. Other typical aerogel-based sol–gel inks including a silica aerogel-based sol–gel ink (SA ink) and a polyimide aerogel-based sol–gel ink (PA ink) for DIW were also demonstrated. Finally, water evaporation experiments were carried out using a 3D-printed carbonized resorcinol–formaldehyde aerogel (CA) to further exhibit the potential applications of this novel technology in solar steam generation. The evaporation rate (1.57 kg m–2 h–1) and efficiency (88.38%) of 3D-printed CA were higher than those of bulk CA (1.21 kg m–2 h–1 and 69.82%). This paper systematically studies the control of DIW parameters for aerogel-based sol–gel inks and shows a potential application in high-efficiency 3D-printed evaporators.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.langmuir.0c03312?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.langmuir.0c03312</a>.Rheological behaviors and thixotropic behaviors of RA inks (Figure S1); rheological behaviors of the SA ink and the PA ink (Figure S2); rapid solidification of the PA ink once it met water (Figure S3); Herschel–Buckley model for RA inks (Figure S4); study of relevant parameters in DIW (Figure S5); extrusion experiments for dextrin (Figure S6); extrusion experiments for RA inks (Figure S7); 3D-printed hydrogels using the RA ink, SA ink, and PA ink (Figure S8); TG-DSC tests for 3D-printed aerogels (Figure S9); uniaxial compression–decompression test for 3D-printed aerogels (Figure S10); derivation of the correlation of the relevant parameters; filament widths at varied applied pressures and writing speeds (Table S1); filament widths at varied heights of the needle to the substrate (Table S2); pressure value, maximum shear stresses, and yield stresses for dextrin and RA inks (Table S3); detailed parameters of bulk CA and 3D-printed CAs (Table S4); and water evaporation data of 3D-printed CAs, bulk CA, and pure water (Table S5).This article has not yet been cited by other publications.

Additive-free graphene-based inks for 3D printing functional conductive aerogels

Direct 3 D Printing of Ultralight Graphene Oxide Aerogel

Direct ink writing of organic and carbon aerogels

Chitosan-based electroconductive inks without chemical reaction for cost-effective and versatile 3D printing for electromagnetic interference (EMI) shielding and strain-sensing applications

3D Printing of Graphene Aerogels.

EMI Shielding and Strain-Sensitive Tape Based on Ultraprecise 3D Printed Graphene Oxide Aerogel Microlattices

Waterborne Graphene- and Nanocellulose-Based Inks for Functional Conductive Films and 3D Structures

3D Printing High‐Resolution Conductive Elastomeric Structures with a Solid Particle‐Free Emulsion Ink

Generalized 3D Printing of Graphene-Based Mixed-Dimensional Hybrid Aerogels

Silicate-Based Electro-Conductive Inks for Printing Soft Electronics and Tissue Engineering

3D printing of architectured graphene-based aerogels by cross-linking GO inks with adjustable viscoelasticity for energy storage devices

3D-Printed Interfacially Jammed Emulsion Aerogels

Ecofriendly Polymer–Graphene‐Based Conductive Ink for Multifunctional Printed Electronics

3D Printing of Ultralow-Concentration 2D Nanomaterial Inks for Multifunctional Architectures

Graphene Inks Printed by Aerosol Jet for Sensing Applications: The Role of Dispersant on the Inks' Formulation and Performance

3D Printed Polyimide Nanocomposite Aerogels for Electromagnetic Interference Shielding and Thermal Management

Versatile Direct Writing of Aerogel-Based Sol–Gel Inks

3D Printing of Multifunctional Conductive Polymer Composite Hydrogels

Water-based and inkjet printable inks made by electrochemically exfoliated graphene

Conductive graphene-based coagulated composites for electronic printing applications

Effect on Electrical Conductivity of Graphene Nanoparticle Filled Epoxy Conductive Ink