Abstract:Narrow-band response photodetectors are widely used in situations where specific light wavelengths need to be detected, such as communication. imaging, surveillance, etc. These detectors require not only the narrowest spectral response window, but also the highest external quantum efficiency (EQE) within the response window. Generally, the semiconductor photoactive layer in the photodetector will absorb the photons with energy greater than the band gap, and the spectral response window is usually wide, so it needs to combine with the filter of specific wavelength to achieve narrow band response. However, the introduction of filters, in addition to the increased cost, will inevitably lead to additional light reflection losses, which will significantly reduce EQE. When the film thickness of the heterojunction is up to inn, the narrow-band response near the band edge can be achieved without a filter. However, the problem brought by thick film is that the photocurrent also decreases, resulting in lower EQE (<30%) of the device. Although higher reverse bias increases the photocurrent and EQE, it also increases the collection probability of short-wave photogenerated carriers, thus damaging the narrow-band response. By greatly reducing the proportion of organic receptors and donors in the micron-size photoactive layer, the narrow-band response window of ca. 650 mu was achieved, and the EQE was up to ca. 53500% under -60 V reverse bias. This kind of organic photodetector achieving the photomultiplication mainly attributes to the trapped charges at the photoactive layer/electrode interface which will capture the photogenerated electrons (holes), and when the photogenerated electrons (holes) are collected, the electric neutral balance in the photoactive layer is broken. The trapped photogenerated electrons (holes) at the interface will cause the change of interface potential energy, which induces the interface band bending of the photoactive layer, and promotes the metal electrode to inject holes into the photoactive layer to maintain the neutral balance. Because the injection current is much higher than the photoelectric current, the superposition of the two can significantly increase EQE and even produce gain. However, the idea of obtaining higher EQE by further increasing the concentration of interfacial trapped electrons is difficult to be realized by increasing the proportion of receptors, which not only reduces EQE, but also increases the full width at half maximum (FWHM) of the response window and destroys the narrow-band response. In this work, the structure of ITO/poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT)/poly(3-hexylthiophene) (P3HT)/[6,6]-phenyl-C61-isomethyl butyrate (PCBM)/aluminum (Al) has been prepared. By optimizing the thermal annealing time and PCBM concentration, the EQE at -60 V was successfully improved from 52946.8% to 68470.9%, which is the highest gain of narrow-band response organic photodetector so far, and the FWHM of ca. 28 tun remains unchanged. We used Nano-IR to confirm that EQE enhancement was attributed to thermal annealing induced diffusion of PCBM into P3HT, thus optimizing the electron trap concentration distribution at the interface between the active layer and the metal top electrode and enhancing carrier injection.

Simultaneous Photomultiplication Improvement and Response Acceleration for High-Performance Lateral Polymer Photodetectors Based on Bulk Heterojunction

Photovoltaic Mode Ultraviolet Organic Photodetectors with High On/Off Ratio and Fast Response

Lateral Polymer Photodetectors Using Silver Nanoparticles Promoted PffBT4T-2OD:PC61 BM Composite

Optimizing electron injection barriers and hole-trapping ability for high-performance photomultiplication-type ternary organic photodetectors

Efficient All‐Polymer Photomultiplication‐Type Organic Photodetectors with Prolonged Crystallization Process

High-responsivity, High-detectivity Photomultiplication Organic Photodetector Realized by a Metal-Insulator-Semiconductor Tunneling Junction

High Performance Photomultiplication Perovskite Photodetectors with PC60BM and NPB As the Interlayers

Transient analysis of photomultiplication-type organic photodiodes

Strategies for achieving high-performance photomultiplication-type organic photodetectors and their promising applications

Recent progress on photomultiplication type organic photodetectors

Dual-Band Photomultiplication-Type Organic Photodetectors with Ultrahigh Signal-to-Noise Ratios

Smart Strategy: Transparent Hole-Transporting Polymer as a Regulator to Optimize Photomultiplication-type Polymer Photodetectors

Bias-Switchable Photomultiplication and Photovoltaic Dual-Mode Flexible Near-Infrared Organic Photodetector

Improving the Photomultiplication in Organic Photodetectors with Narrowband Response by Interfacial Engineering

Photomultiplication‐Type Organic Photodetectors for Near‐Infrared Sensing with High and Bias‐Independent Specific Detectivity

Enhanced Gain in Organic Photodetectors Using the Polymer with Singlet Open‐Shell Ground State

Energy level gradient trapping based on different work functions of ZnO enhancing response and stablity for lateral photodetectors

Revealing The Working Mechanism Of Polymer Photodetectors With Ultra-High External Quantum Efficiency

Mitigating Dark Current and Improving Charge Collection for High-Performance Near-Infrared Organic Photodiodes Via P-Doping Strategy

Enhanced Detectivity of Organic Photodetectors with a Non-Conjugated Polymer Additive

Addressing Responsivity‐Noise Trade‐Off by Van Der Waals Multilayer Two‐Phase Heterojunction for Large LDR Organic Photodetectors