Abstract:Conventional fluids used in fission‐based water‐cooled nuclear reactors have lower heat transfer coefficients and thermal conductivity, prompting researchers to explore high‐performance fluids to enhance heat transfer and prevent core meltdown during accidents. It is crucial to investigate fluids that can improve thermal hydraulic characteristics, such as the heat transfer coefficient, critical heat flux (CHF), and minimum departure from nucleate boiling ratio (MDNBR). This study investigates the effectiveness of nanofluids in enhancing heat transfer parameters, including thermal conductivity and heat capacity. Results indicate that the silver water nanofluid outperformed the other nanofluids and pure water. The silver water nanofluid demonstrated a 67.15 % improvement in the average heat transfer coefficient and a 45.23 % enhancement in MDNBR compared to pure water. This study underscores the promise of nanofluids, particularly Ag–H2O, in enhancing the thermal performance and safety of water‐cooled nuclear reactors. Future research should continue to explore various nanofluids and their applications to further optimize reactor design and operation, ensuring both efficiency and safety in nuclear energy production. Conventional fluids used in fission‐based water‐cooled nuclear reactors have lower heat transfer coefficients (HTCs) and thermal conductivity, which has led researchers to explore high‐performance fluids that can enhance heat transfer in routine operation and prevent core meltdown in the case of accidents. It is important to investigate a wide range of fluids that can help designers improve thermal hydraulic characteristics, such as HTC, critical heat flux, and minimum departure from nucleate boiling ratio (MDNBR). In this study, the effectiveness of nanofluids in enhancing heat transfer parameters, including thermal conductivity and heat capacity, was investigated. Four different nanofluids (Al2O3–H2O, ZrO2–H2O, Ag–H2O, and Si–H2O) with pure water as the primary coolant in an HPR‐1000 nuclear reactor were compared using computational methods. Due to computational limitations, only the flow channel among four fuel rods with the highest power density in the core was simulated using Eulerian computational fluid dynamics. The results of this study show that silver water (Ag–H2O) nanofluid outperformed other nanofluids and pure water. It had a higher average HTC and MDNBR, with a 67.15 % and 45.23 % improvement, respectively, compared to pure water. The fuel rod wall temperature was also reduced by 28.5 K with Ag–H2O compared to water. Comparison of current simulated results with literature data shows a good agreement.

Experimental study on the CHF enhancement effect of nanofluids on the oxidized low carbon steel surface

Experimental Study on CHF Using a Full Scale 2-D Curved Test Section with Additives and SA508 Heater for IVR-ERVC Strategy

CHF Enhancement by γ-Fe2O3 Nanofluids with Pool Boiling Condition on a Downward-Facing Plane

Numerical simulation study of boiling Critical Heat Flux characteristics of graphene nanofluids

CHF enhancement of downward-facing saturated pool boiling on the SCGS-modified surfaces with multi-scale conical pin fin structures

CHF enhancement by honeycomb porous plate in saturated pool boiling of nanofluid

The Effects of Surface Orientation, Heater Size, Wettability, and Subcooling on the Critical Heat Flux Enhancement in Pool Boiling

Experimental Research on Influence of Real Surface Material and Aging Effect on ERVC-CHF of RPV

CHF and heat transfer enhancement by SiO 2 nanofluids on a inclined downward facing heating surface

Boiling and quenching heat transfer advancement by nanoscale surface modification

Experimental study of the key factors of improving CHF to support CAP1400 IVR strategy

Enhancement of the Critical Heat Flux for Downward-Facing Saturated Pool Boiling on the Reticular Hollow Shell Structure Surfaces

Experimental study on the pool boiling performance of a highly self-dispersion TiO2 nanofluid on copper surface

Pressure effect on CHF enhancement in pool boiling of nanofluids

Study of flow boiling heat transfer characteristics of critical heat flux using carbon nanotubes and water nanofluid

Improved Heat Transfer Capabilities of Nanofluids—An Assessment Through CFD Analysis

Enhancing Thermal–Hydraulic Performance in Nuclear Reactor Subchannels with Al2O3 Nanofluids: A CFD Analysis

Recent Advances in the Critical Heat Flux Amelioration of Pool Boiling Surfaces Using Metal Oxide Nanoparticle Deposition

An Experimental Study of Boiling Heat Transfer During Quenching of Nanofluids with Carbon Nanotubes of Various Sizes

Effect of magnetic field and surfactant on the boiling heat transfer and CHF of magnetic nanofluids on a downward heating surface

The effects of nanoparticles on pool boiling and critical heat flux