Abstract:The non-equilibrium phase evolution during laser powder bed fusion (LPBF) of AlSi10Mg alloy is thoroughly characterized and analyzed by means of advanced electron microscopy and analytical simulation of rapid solidification phenomenon. The evolution of microstructural strengthening agents such as inter-cellular eutectic phase and intra-cellular precipitates is presented in correspondence with the local variation of cellular/dendritic solidification patterns within a typical melt pool. The eutectic phase exhibits two different morphologies: lamellar and fibrous. As with the cell size variation, the overall volume fraction of eutectic phase and the lamella spacing is shown to gradually decrease by moving away from the melt-pool boundary (MPB), i.e., through crossing over from a coarse to a fine cellular zone. The eutectic-free regions within the α-Al cells contain a large number density of nano-sized precipitates that are predominantly Si-rich and are either fully or semi-coherent with the Al matrix. The formation of nano-precipitates is linked to the increased (non-equilibrium) solubility limits of α-Al cells due to the rapid solidification effect. For the first time, we identify such nano-precipitates with non-equilibrium crystal structures and morphologies: "Spheres" and "Ellipsoids" with Face Centered Cubic (FCC), and "Plates" and "Needles" with a Diamond Cubic (DC) superlattice structure that emerges from within the Al matrix. The microstructure in the heat-affected zone (HAZ) right underneath the MPB exhibits an absence of cell boundaries and eutectic phases while consisting primarily of large Si-rich and Mg-rich precipitates. Finally, the local variation of nano-hardness across a solidified melt pool is shown to correlate well with the corresponding profile of microstructural refinement, i.e., exhibiting a minimum at the HAZ and a peak at around the melt-pool centerline. The findings here can significantly advance the state of knowledge for the strengthening behavior in an as-built LPBF-processed AlSi10Mg alloy.

Laser Powder Bed Fusion of Hard‐Phase Containing Co‐Base Alloy

High-temperature Oxidation Behavior of AlCoCrCuFeNi High-Entropy Alloy by Selective Laser Melting

Laser powder bed fusion of an Al-Cr-Fe-Ni high-entropy alloy produced by blending of prealloyed and elemental powder: process parameters, microstructures and mechanical properties

Approach to Estimate the Phase Formation and the Mechanical Properties of Alloys Processed by Laser Powder Bed Fusion via Casting

Laser powder bed fusion of compositionally graded CoCrMo-Inconel 718

Processability and Optimization of Laser Parameters for Densification of Hypereutectic Al–Fe Binary Alloy Manufactured by Laser Powder Bed Fusion

Microstructure Evolution of FeNiCoCrAl1.3Mo0.5 High Entropy Alloy during Powder Preparation, Laser Powder Bed Fusion, and Microplasma Spraying

PBF-EB of Fe-Cr-V Alloy for Wear Applications

Laser Powder Bed Fusion Processing of Low Cost CoCrFeNiMoxNby High Entropy Alloys with Promising High-Temperature Properties via In Situ Alloying Commercial Powders

Preparation of Cu-Cr-Zr Alloy by Laser Powder Bed Fusion: Parameter Optimization, Microstructure, Mechanical and Thermal Properties for Microelectronic Applications

Influence of an Increasing Alloying Content on the Microstructure of a High‐Speed Steel in the Laser‐Powder Bed Fusion Process

Processing-microstructure relationships in ferrous alloys via mixed powder laser powder bed fusion

Establishing a process route for additive manufacturing of NiCu-based Alloy 400: an alignment of gas atomization, laser powder bed fusion, and design of experiments

Surface hardening of CrCoFeNi high-entropy alloys via Al laser alloying

Processability of high-strength aluminum 6182 series alloy via laser powder bed fusion (LPBF)

Laser powder bed fusion of a tungsten-nickel-ferrum alloy via in-situ alloying: Densification, microstructure, and mechanical properties

PBF-LB/M of Low-Alloyed Steels: Bainite-like Microstructures despite High Cooling Rates

A Micro-Computed Tomography Comparison of the Porosity in Additively Fabricated CuCr1 Alloy Parts Using Virgin and Surface-Modified Powders

Development of a Laser Powder Bed Fusion Process Tailored for the Additive Manufacturing of High-Quality Components Made of the Commercial Magnesium Alloy WE43

Rapid Solidification and Non-equilibrium Phase Constitution in Laser Powder Bed Fusion (LPBF) of AlSi10Mg Alloy: Analysis of Nano-precipitates, Eutectic Phases, and Hardness Evolution

Requirements for Processing High-Strength AlZnMgCu Alloys with PBF-LB/M to Achieve Crack-Free and Dense Parts