Abstract:The Journal of Strain Analysis for Engineering Design, Ahead of Print. In the present work, the process chain in tube production by roll forming of the steel 34MnB5 was examined in more detail. The process chain consisting of the steps (i) roll forming, (ii) HFI welding, and then (iii) straightening and final calibration was mapped using the finite element method. In addition to the pipe geometry, the residual stress distribution was considered as an essential target value for the assessment of the performance of the tubes under service conditions. The objective of the project is to describe the manufacturing process and thus the processing induced residual stress distributions as realistically as possible. For a more detailed characterization of the process and above all for the validation of the numerical simulations, experimental residual stress analyses were carried out for the final state of the tubes using complementary analysis methods. The contour method was used to determine the 2D-distribution of residual stresses across the transverse and longitudinal sections of the manufactured pipes. These measurements were supplemented by local residual stress analyses using the incremental hole drilling method and X-ray residual stress analyses. The work thus pursues both a methodical approach to the analysis of the internal stresses induced by the process using complementary methods and also a manufacturing approach to the analysis and evaluation of the production chain. In particular for the axial components of the residual stresses, it can be shown that experimentally determined residual stresses correlate well with the numerically calculated values. The contour method is excellently suited to monitor the uneven distribution of the internal stresses over the pipe cross-section. The results of the simulation show that the overall residual stress distribution that is determined using the contour method mainly results from the plastic strains introduced by the roll forming process. X-ray and hole drilling analyses are shown to be more suitable for measuring locally present residual stresses at defined positions on the outer tube surface. In this way it can be shown that the simulation approach described provides an accurate model of the process.

Residual Stress Induced by Phase Transformation and its Role in the Delayed Cracking Performance of 22MnB5 Hot Roll Bending Pipes

Impact of Hot Bending on the High-Temperature Performance and Hydrogen Damage of 2.25Cr-1Mo-0.25v Steel

Types and Cause of Cold Bending Crack Defects of Welded Pipe

Strain-hardening Behavior of High Grade Linepipe Steel and Its Influence Factors

Quenching Stress of Hot-Rolled Seamless Steel Tubes under Different Cooling Intensities Based on Simulation

Experimental study on the compression mechanical behaviour of steel pipes with mechanically induced pitting corrosion

Experimental and Fea Investigations on the Fracture Properties of Pipe Structures under Internal Pressure in Dbtt Region

Initiation of Stress Corrosion Cracks in X80 and X100 Pipe Steels in Near-Neutral Ph Environment

Constraint Effect on the Ductile Crack Growth Resistance of Circumferentially Cracked Pipes

Investigation of Constitutive Relationship and Dynamic Recrystallization Behavior of 22mnb5 During Hot Deformation

The Fatigue Crack Initiation Life of X60 Pipeline Steel after Pre-tension Deformation

Hot Deformation Behavior and Recrystallization Analysis of Pipe 20CrNiMo Steel

Three-dimensional Finite Element Analysis of Residual Stresses in Circumferential Welds of 2205/X65 Bimetallic Pipe

Experimental and numerical analysis of residual stresses induced by the manufacturing process of longitudinal welded tubes

Experimental Study on the Causes of Cracking of High-Strength Steel During Bending

Investigation on axial deformation of high strain line pipe

Mechanical Analysis about Effect of Bending Deformation on Stress Recovery Characters in the Fe-17Mn-10Cr-5Si-4Ni Alloy

Finite element and experiment analysis of welding residual stress in S355J2 steel considering the bainite transformation

Research on Deformation Property of 316LN Nuclear Main Pipe Steel at Elevated Temperature

Cyclic plasticity behavior and deformation mechanism of 1Cr18Ni10Ti pressure pipe subjected to in-service loadings

Analysis of Crack Propagation of Annular Butt Weld and Distribution of Weld-Induced Residual Stress