Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Quasi-solid-state electrolyte for ultra-high safety and cycle stability battery

High-performance gel electrolyte for enhanced interface compatibility and lithium metal stability in high-voltage lithium battery

4.2 V poly(ethylene oxide)-based all-solid-state lithium batteries with superior cycle and safety performance

Porous Composite Gel Polymer Electrolyte with Interfacial Transport Pathways for Flexible Quasi Solid Lithium-Ion Batteries.

Enhanced Ionic Conductivity and Interface Stability of Hybrid Solid-State Polymer Electrolyte for Rechargeable Lithium Metal Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

Molecular Reactivity and Interface Stability Modification in In‐Situ Gel Electrolyte for High Performance Quasi‐Solid‐State Lithium Metal Batteries

A High Ion Conductive Solid Electrolyte Film and Interface Stabilization Strategy for Solid-state Li-S Battery

Supramolecular polymer cross-linking gel electrolyte for highly stable quasi-solid-state lithium metal batteries

Highly Conductive, Flexible, and Nonflammable Double-Network Poly(ionic Liquid)-Based Ionogel Electrolyte for Flexible Lithium-Ion Batteries.

Ionic liquid boosting the electrochemical stability of a poly(1,3‐dioxolane) gel electrolyte for high‐voltage solid‐state lithium batteries

Flame Retardant and Stable Li1.5Al0.5Ge1.5(PO4)3-Supported Ionic Liquid Gel Polymer Electrolytes for High Safety Rechargeable Solid-State Lithium Metal Batteries

An Ionic Liquid‐Based Gel Electrolyte: Formation Mechanism and Feasibility for Lithium Metal Batteries

An Integrate and Ultra-Flexible Solid-State Lithium Battery Enabled by in Situ Polymerized Solid Electrolyte

A high-safety electrolyte based on functionalized ionic liquid and polyurethane for lithium batteries

Solid Polymer Electrolytes with Dual Salts Enhance Lithium-Metal Interfacial Stability for Long Cycle Performance of Lithium Batteries

Ultrathin, flexible, solid polymer composite electrolyte enabled with aligned nanoporous host for lithium batteries

High-capacity all-solid-state lithium battery with stable interfaces enabled by ultra-thin polyvinylidene fluoride/Li 3 InCl 6 composite solid electrolyte

An Advanced Gel Polymer Electrolyte for Solid-State Lithium Metal Batteries

Fluorinated functional groups enhanced composite in-situ gel electrolytes for high voltage cathode of quasi solid-state lithium battery

Long‐cycling and High‐voltage Solid State Lithium Metal Batteries Enabled by Fluorinated and Crosslinked Polyether Electrolytes