Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Molecular Reactivity and Interface Stability Modification in In‐Situ Gel Electrolyte for High Performance Quasi‐Solid‐State Lithium Metal Batteries

In-situ Generation of Poly(ionic Liquid) Flexible Quasi-Solid Electrolyte Supported by Polyhedral Oligomeric Silsesquioxane/polyvinylidene Fluoride Electrospun Membrane for Lithium Metal Battery

Internal in Situ Gel Polymer Electrolytes for High-Performance Quasi-Solid-state Lithium Ion Batteries

Regulating Micro‐phase Structure in Plastic Crystal Gel Polymer Electrolyte for Quasi‐Solid‐State Lithium Metal Batteries

High-performance gel electrolyte for enhanced interface compatibility and lithium metal stability in high-voltage lithium battery

Fluorinated functional groups enhanced composite in-situ gel electrolytes for high voltage cathode of quasi solid-state lithium battery

Engineering Molecule‐Designed In Situ Polymerization on Al‐Doped Molecular‐Sieve Framework Enables Robust Quasi‐Solid‐State Lithium Batteries

Constructing a Stable Lithium Metal-Gel Electrolyte Interface for Quasi-Solid-State Lithium Batteries.

Molecular engineering of a gel polymer electrolyte via in-situ polymerization for high performance lithium metal batteries

In Situ Co-Growth Lif-Li3n Rich Dual-Protective Layers Enable High Interface Stability for Solid-State Lithium-Metal Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

In Situ Construction of Ether-Based Composite Electrolyte with Stable Electrode Interphase for High-Performance Solid State Lithium Metal Battery

Stabilizing Solid‐state Lithium Metal Batteries Through in Situ Generated Janus‐heterarchical LiF‐rich SEI in Ionic Liquid Confined 3D MOF/Polymer Membranes

Polymer–inorganic solid–electrolyte interphase for stable lithium metal batteries under lean electrolyte conditions

A Multifunctional Silicon‐Doped Polyether Network for Double Stable Interfaces in Quasi‐Solid‐State Lithium Metal Batteries

In Situ Formed Gel Polymer Electrolytes Enable Stable Solid Electrolyte Interface for High-Performance Lithium Metal Batteries

Reinforcing Concentrated Phosphate Electrolytes with In-Situ Polymerized Skeletons for Robust Quasi-Solid Lithium Metal Batteries

Ionic Liquid Functionalized Gel Polymer Electrolytes for Stable Lithium Metal Batteries

Supramolecular polymer cross-linking gel electrolyte for highly stable quasi-solid-state lithium metal batteries

In Situ Polymerization Design of a Quasi-Solid Electrolyte Enhanced by NMP Additive for Lithium Metal Batteries

Fluorinating Solid Electrolyte Interphase by Regulating Polymer–Solvent Interaction in Lithium Metal Batteries