Abstract:With the advancement of laser powder bed fusion (LPBF) for aluminum alloys, developing novel lightweight Al–Li alloy systems present enormous potential for aerospace applications. Conventional Al–Mg–Li alloys exhibit low densities but suffer from poor strength due to the lack of inherent strengthening phases. In the present work, a novel lightweight Al–Mg–Li–Ag-Sc-Zr alloy was developed for LPBF after optimizing the processing parameters. The as-built alloy featured a bimodal microstructure consisting of fine equiaxed grains and columnar grains. The submicron primary Al 3 (Sc, Zr) phases with a cubic L 1 2 structure served as inoculants for grain refinement and exhibited good coherency with the α-Al matrix. Besides, submicron spherical quasicrystalline T-Mg 32 (Al, Ag) 49 phases of and nanometer rod-shaped S 1 –Al 2 MgLi phases were scattered inside the grains. These results produced a yield strength (σ y ) of 286 ± 8 MPa, ultimate tensile strength (σ UTS ) of 406 ± 3 MPa, and elongation at fracture (ε f ) of 12.5 ± 0.3%. The direct aging at 325 °C for 12 h led to an increase in hardness to a peak value of 170 HV. The secondary phases at the grain boundaries were breached and a large amount of submicron T and S 1 phases within the grains were prominently increased. Besides, spherical Al 3 (Sc, Zr, Li) and tiny δ′-Al 3 Li precipitates were observed in the α-Al matrix. A considerably enhanced σ y of 375 ± 12 MPa and σ UTS of 469 ± 4 MPa were achieved mainly due to the particle strengthening but decreased ε f to 5.8 ± 0.2%. The alloys in both states exhibited a moderate work-hardening capability. The feasibility of LPBF for lightweight Al–Li alloy was successfully established but required further optimization of the alloy composition.

Exploration of Alloying Elements of High Specific Modulus Al–Li Alloy Based on Machine Learning

Machine learning assisted design of aluminum-lithium alloy with high specific modulus and specific strength

Atomic insights for elevated modulus in Al–Li alloys: synergies and design strategy

Accelerated discovery of high-strength aluminum alloys by machine learning

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

Machine-learning assisted compositional optimization of 2xxx series aluminum alloys towards tensile strength

Exploring the mechanism of plastic deformation in BCC Mg-Li-Al alloys via Machine learning Molecular dynamics simulations

Machine Learning Design of Aluminum-Lithium Alloys with High Strength

Microstructure and Mechanical Properties of Al-Li Alloys with Different Li Contents Prepared by Selective Laser Melting

Machine Learning Driven Design of High-Performance Al Alloys

Research Progress of New Generation of Aluminum‐Lithium Alloys Alloying

Alloy design and properties optimization of multi-component alloy based on solidification characteristics

Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: A review

Accelerated Design of High-Performance Mg-Mn-based Magnesium Alloys Based on Novel Bayesian Optimization

A New High Strength and High Tolerance-Resistance Al-Li Alloy

Machine learning-based identification method of new strengthening element and the study on Al-Zn-Mg-Cu-Zr-Hf alloy

Accelerated Design of Al-Zn-Mg-Cu Alloys Via Machine Learning

Engineering ultra-strong Mg-Li-Al-based light-weight alloys from first principles

Composition optimization of cobalt-free Fe-Cr-Ni-Al/Ti multi-principal element alloys for strength-ductility trade-off based on machine learning

Designing Al-Zn-Mg-Cu Alloys Using Machine Learning