Abstract:Sulfur is a promising active material for the lithium rechargeable batteries because of its high theoretical capacity, a relatively low cost, and an environmentally friendly nature. Lithium–sulfur battery with a high-energy-density is regarded as a third-generation rechargeable battery with high potential for commercialization. The well charged and discharged lithium–sulfur battery can generate specific energy density of up to 600 W∙h kg −1 . However, the charging product, sulfur, and the discharging product, lithium sulfide, both have low conductivity, which lead to low active material utilization and excessive addition of conductive materials, lowering the active material content and performance in the cathode region. The liquid active material, polysulfides, formed in the middle of the cycling reaction will dissolve in the electrolyte, causing leakage to the lithium anode to form a non-reactive lithium sulfide layer, causing severe capacity fading. Furthermore, the repeated transformation of sulfur (solid-state), polysulfides (liquid-state), and lithium sulfur (solid-state) active materials led to the sluggish battery reaction and irreversible electrolyte consumption. All and all, the chemical and physical properties of the sulfur and the combination with lithium resulted in low active material utilization, low cycling ability, low capacity-retention rate, and shortened cycle life. To fully realize the potential of the high-energy-density lithium–sulfur battery, the cathode material, configuration, and fabrication must be carefully considered. Herein, a sulfur cathode fabricated by a hot-pressing method and the evaluation of different porous substrate was also conducted. Porous conductive network is a common cathode material, which provides a large surface area and great polysulfides absorbability. However, as a result of high-sulfur-loading and lean-electrolyte cathode batteries, a low specific capacity and short cycle life are discovered, which is affected by the high electrolyte consumption. Accordingly, a carbon electrospun substrate with a non-nanoporous structure was introduced as the conductive network to achieve the high-energy-density battery design. To fabricate the free-standing sulfur cathode, sulfur powder was loaded between two porous carbon electrospun substrate by a hot-pressing technique. The cathode consists of three layers: carbon current collector, melt-in sulfur layer, and carbon interlayer, forming a sandwich-like cathode. With this design, we can accommodate high areal loading of sulfur (8 mg cm −2 ) in the cathode area while lessening the conductive additive (sulfur content of 73 wt%). The hot-pressed electrospun cathode, conducted under low electrolyte usage (i.e., the low electrolyte-to-sulfur ratio of 7 μL mg −1 ) can achieve excellent energy density (11.8 mW∙h cm −2 ) with a stable areal capacity up to 5.9 mA∙h cm − 2 let alone with an extended cycle life over 200 cycles. Furthermore, this devised cathode can also retain excellent cycling ability with lower ratios of electrolyte to sulfur (6–4 μL mg −1 ) and great rate dependent performance up to C/2 cycling rate. Figure 1

Low Tortuosity and Reinforced Concrete Type Ultra‐Thick Electrode for Practical Lithium–Sulfur Batteries

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

Reconfiguring Organosulfur Cathode by Over-Lithiation to Enable Ultrathick Lithium Metal Anode toward Practical Lithium–Sulfur Batteries

High-Performance Lithium–Sulfur Batteries with a Cost-Effective Carbon Paper Electrode and High Sulfur-Loading

A compact 3D interconnected sulfur cathode for high-energy, high-power and long-life lithium-sulfur batteries

A strategy to achieve high loading and high energy density Li-S batteries

Rationally Design a Sulfur Cathode with Solid‐Phase Conversion Mechanism for High Cycle‐Stable Li–S Batteries

Cathode Design and Evaluation for the High-Sulfur-Loading, Lean-Electrolyte Lithium–Sulfur Battery

Flexible and Self-Supported Sulfur Cathode for High-Energy-Density Lithium-Sulfur Batteries

Synergistic Electrocatalyst-Cathode Architecture for Stable Long-Term Cycling Lithium-Sulfur Batteries

Sulfur-infiltrated porous carbon microspheres with controllable multi-modal pore size distribution for high energy lithium–sulfur batteries

Confining Sulfur in Integrated Composite Scaffold with Highly Porous Carbon Fibers/Vanadium Nitride Arrays for High‐Performance Lithium–Sulfur Batteries

Highly integrated sulfur cathodes with strong sulfur/high-strength binder interactions enabling durable high-loading lithium–sulfur batteries

Three-dimensional Spongy Framework As Superlyophilic, Strongly Absorbing, and Electrocatalytic Polysulfide Reservoir Layer for High-Rate and Long-Cycling Lithium-Sulfur Batteries

3D Holey Graphene/Polyacrylonitrile Sulfur Composite Architecture for High Loading Lithium Sulfur Batteries

Multilevel structured carbon film as cathode host for Li-S batteries with superhigh-areal-capacity

Engineering the Conductive Network of Metal Oxide‐Based Sulfur Cathode toward Efficient and Longevous Lithium–Sulfur Batteries

Engineering Peculiar Cathode Electrolyte Interphase toward Sustainable and High‐Rate Li–S Batteries

Constructing 1D/2D Interwoven Carbonous Matrix to Enable High-Efficiency Sulfur Immobilization in Li-S Battery

Integrated interconnected porous and lamellar structures realized fast ion/electron conductivity in high-performance lithium-sulfur batteries

Long-Life, High-Efficiency Lithium–Sulfur Battery from a Nanoassembled Cathode