Abstract:Defect ordered and low dimensional Cs 3 Bi 2 I 9 planar perovskites have garnered enormous significance in photovoltaic applications due to their remarkable stability against oxygen, heat, and moisture. Despite these advantages, the power conversion efficiencies of Cs 3 Bi 2 I 9 -based planar perovskites remain relatively low. This is primarily attributed to their wide band gap of approximately 2 eV and losses due to interfacial charge recombination. To resolve this issue, this article proposes a novel design of Cs 3 Bi 2 I 9 –La 2 NiMnO 6 based dual absorber composition to form a ITO/ETL/Cs 3 Bi 2 I 9 /La 2 NiMnO 6 (LNMO)/HTL multi-heterojunction perovskite solar cell (PSC) architecture. Incorporating La 2 NiMnO 6 oxide material as secondary multifunctional double perovskite absorber layer (DPAL), which possesses a lower band gap of 1.05 eV, as a secondary absorber layer enhances efficient charge separation. This material functions as a hole transport conductor, facilitating the creation of a cascade band-matched hole extraction system with the Cu 2 ZnSnS 4 (CFTS) hole transport material (HTM). Optimized optical response along with precisely aligned energy levels of the proposed Cs 3 Bi 2 I 9 –La 2 NiMnO 6 (LNMO) absorber composition greatly attributes in enhanced optical absorption with reduced recombination losses. The critical device parameters of the proposed PSC architecture have been intensively optimized through SCAPS-1D simulator to attain a substantially affordable power conversion efficiency (PCE) of 26.02%%, short circuit current ( J sc ) of 42.7 mA/cm 2 , open circuit voltage ( V oc ) of 0.863 V, and fill factor ( FF ) of 75.01% device defect density of 10 15 cm −3 under AM 1.5 photo illumination. Notably, the utilization of a dual-absorber structure comprising Cs 3 Bi 2 I 9 and La 2 NiMnO 6 materials proves to be significantly more efficient in terms of quantum efficiency and wide spectral coverage at optimal values compared to using either material alone as single absorbers. The proposed model achieves a peak efficiency of approximately 90.22% over a spectral range of 300–1200 nm, surpassing the efficiency of 80% attained with a single Cs 3 Bi 2 I 9 absorber covering a spectral range of 300–980 nm. Additionally, it outperforms the efficiency of 83% achieved by the single La 2 NiMnO 6 (LNMO) absorber within the spectral range of 300–1200 nm.

Analytical Model of All-Inorganic 2-D Ruddlesden-Popper (RP) Layered Halide Perovskite Solar Cells and Their Performance Optimization

Inorganic perovskite solar cells: an emerging member of the photovoltaic community

A Novel Perovskite Solar Cell Comprising CsPbI2Br/Cs2SnI6 (CsGeI3) Cascade Absorbing Bilayer and Cr2O3 Electron Transport Material: A Theoretical Comparison Study

Exploring the potential of CsPbI3/CsPbBr3 heterojunction as an absorber layer in perovskite solar cells: a numerical and experimental study

A Comprehensive Study of Electronic, Optical, and Thermoelectric Characteristics of Cs2PbI2Br2 Inorganic Layered Ruddlesden-Popper Mixed Halide Perovskite through Systematic First-Principles Analysis

Structural optimization of inverted CsPbI2Br perovskite solar cells for enhanced performance via SCAPS-1D simulation

Numerical Simulation of All Inorganic CsPbIBr2 Perovskite Solar Cells with Diverse Charge Transport Layers using DFT and SCAPS-1D Frameworks

Comprehensive performance analysis of perovskite solar cells based on different crystalline structures of MAPbI3

CsPbI3 Based All‐Inorganic Perovskite Solar Cells: Further Performance Enhancement of the Electron Transport Layer‐Free Structure from Device Simulation

Design and performance optimization of a novel tri-layer unleaded all inorganic lead-free mixed halide CsSnI 3-x Br x heterojunction solar cell

Improvement of photovoltaic response in perovskite solar cell via all inorganic lead free cubic double La2NiMnO6/Cs3Bi2I9 based graded absorber architecture

Promising photovoltaic and solid-state-lighting materials: two-dimensional Ruddlesden-Popper type lead-free halide double perovskites Csn+1Inn/2Sbn/2I3n+1 (n=3) and Csn+1Inn/2Sbn/2Cl3n+1/Csm+1Cum/2Bim/2Cl3m+1 (n=3, m=1)

Optimization of all inorganic perovskite solar cell with dual active layers for beyond 29% efficiency

Design and numerical investigation of CsPbI3/CsSn0.5Ge0.5I3 double‐absorption‐layer heterojunction perovskite solar cells based on SCAPS‐1D

CsPbI3-Perovskite Quantum Dot Solar Cells: Unlocking Their Potential through Improved Absorber Layer Characteristics and Reduced Defects

Synergistic Passivation With Phenylpropylammonium Bromide for Efficient Inverted Perovskite Solar Cells

Maximizing photovoltaic performance of all-inorganic perovskite CsSnI 3-x Br x solar cells through bandgap grading and material design

Design and simulation investigations on charge transport layers-free in lead-free three absorber layer all-perovskite solar cells

Theoretical Analysis on Interfacial Dynamics Between Charge Transport Layer and Different Absorbers in Pb-free All Inorganic Perovskites Solar Cells

Numerical Simulation of Cs2AgBiBr6-based Perovskite Solar Cell with ZnO Nanorod and P3HT as the Charge Transport Layers

Efficient and Stable CsPbI3 Perovskite Solar Cells with Spontaneously Formed 2D-Cs2pbi2cl2 at the Buried Interface