Abstract:The purpose of this study is to quantitatively analyze the effect of strain path on roughness evolution of free surface during plastic deformation. Firstly, the crystal plastic finite element model for a representative volume element (RVE) of polycrystalline is established, including the polycrystalline geometric model and initial topography model. Next, based on two groups of strain path including five typical strain paths, i.e., uniaxial tension (UT), biaxial tension (BT), plane strain tension (PST), plane strain compression (PSC) and in-plane pure shear (PPS), the 3D surface roughness of free surface after the plastic deformation is presented quantitatively. The total change of surface topography can be divided into two parts, which relate to the homogenous deformation and inhomogeneous deformation. In a simple manner, the homogenous deformation and inhomogeneous deformation can correspond with the elastic deformation and plastic deformation respectively. As in the elastic deformation, the effect of the misorientation of the adjacent grains and strain localization in the polycrystalline material on the surface topography has no chance to exert on the very small strain. So the inhomogeneity of polycrystalline material has been ignored in the elastic deformation. For the effect of homogeneous deformation, the relationship between the surface roughness of the deformed surface, initial roughness and strain path is analytically derived. For the contribution of the inhomogeneous deformation to surface roughening, the quantitative relationship between surface roughness of the deformed surface and the strain path is acquired by the mathematical fitting based on hundreds of crystal plasticity finite element simulations. The final surface roughness of the deformed surface is obtained by combining these two parts. Then the experiment of biaxial tension on 6061 aluminum alloy sheet is taken as an example to verify the accuracy of surface roughness calculation. The comparison of experimental results and calculated results shows good consistency. Thereafter the surface roughening phenomena in the plastic deformation are observed at three different scales. The homogeneous deformation does not form additional peaks and valleys but changes the spacing and height of peaks and valleys of the initial surface topography, which brings about the surface roughening at macroscale level. In inhomogeneous deformation, the misorientation of the adjacent grains in the polycrystalline material is taken into consideration, which leads to the grain rotation and generates the additional peaks and valleys of the initial surface topography. The surface roughening due to this part can be seen at the mesoscopic scale. And the step phenomenon caused by slip bands inner the grains is the microscopic scale roughening behavior. This work is beneficial to understand the roughness evolution of free surface quantitatively with the effect of strain path and make out the surface roughening phenomena at different scales.

Coupling effect of plastic deformation and surface roughness on friction behaviors of rough line contact for ground metal surfaces

Effects of Surface Roughness on Sliding Friction in Lubricated-Point Contacts: Experimental and Numerical Studies

Effect of Nanoscale Surface Roughness on Sliding Friction and Wear in Mixed Lubrication

Effects of Interface Friction States on Plastic Deformation in Metal Surface and Bulk

Friction Control by Tailoring Deformation Mechanism of Interfacial Grains in Metals

Effect of Grain Size on the Adhesive and Ploughing Friction Behaviours of Polycrystalline Metals in Forming Process

Effect of surface roughness on sliding friction in lubricated contacts-reciprocal experiment study

Combined Effect of Boundary Layer Formation and Surface Smoothing on Friction and Wear Rate of Lubricated Point Contacts During Normal Running-in Processes

Influence of Nanoscale Textured Surfaces and Subsurface Defects on Friction Behaviors by Molecular Dynamics Simulation.

Surface Effect in Nano-Scale Fretting Contact Problems

Frictional Contacts Between Rough Grains With Fractal Morphology

Effect of Strain Path on Roughness Evolution of Free Surface During Plastic Deformation

A review on plastic deformation induced surface/interface roughening of sheet metallic materials

Mesoscopic coupled plasticity-damage model of rough surface considering size-dependent plasticity

Experimental Study and Simulation Analysis on Friction Behavior of A Mechanical Surface Sliding on Hard Particles

Effect of Wear-Induced Surface Deformation on Stick-Slip Friction of Galvanized Automotive Steels

Experimental and Finite Element Analysis of Plastic Domain Evolution of Rough Surfaces during Contact

Characterization of the Nonuniform Friction Behaviors in Rough Surfaces for the Initial Slip by the Micro-Contact and Deformation Zones

Research Status of Surface Roughening during Plastic Deformation

Friction and Wear in Nanoscratching of Single Crystals: Effect of Adhesion and Plasticity

The Effect of Surface Roughness Characteristics on the Elastic–plastic Contact Performance