Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Two-photon 3D printed spring-based Fabry–Pérot cavity resonator for acoustic wave detection and imaging

All-Fiber Fabry-Perot Resonators Based on Microfiber Sagnac Loop Mirrors

Fabrication of high-Q microresonators in dielectric materials using a femtosecond laser: Principle and applications

3D printed Fabry-Perot acoustic probe with a glass horn tube

Femtosecond Laser Direct Writing of High-Q Microresonators in Glass and Crystals

Ultracompact optical fiber acoustic sensors based on a fiber-top spirally-suspended optomechanical microresonator.

Two-photon 3D printing diaphragm-integrated ring waveguide coupler for ultrasound detection

Extrinsic F-P interferometric fiber ultrasonic sensor using two-photon polymerization 3D printing

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Two-photon 3D printing optical Fabry-Perot microcavity for non-contact pressure detection

Rapid 3D Micro-Printing of Optical Whispering-Gallery Mode Resonators

Fiber-Tip Resonator Excited by Radiation Pressure and Photo-Thermal Effect

An Acoustic Sensor Based on Active Fiber Fabry-Pérot Microcavities

Photothermally Tunable Fabry-Pérot Fiber Interferometer for Photoacoustic Mesoscopy.

Ultrasonic signal detection based on Fabry–Perot cavity sensor

WS 2 -Flake-Sandwiched, Au-Nanodisk-Enabled High-Quality Fabry-Pérot Nanoresonators for Photoluminescence Modulation

High Sensitivity Fiber Acoustic Sensor Tip Working at 1550 Nm Fabricated by Two-Photon Polymerization Technique

Direct 3D-printed ring-resonator photonic circuit on a dual core fiber tip for remote sensing applications

Direct laser-written optomechanical membranes in fiber Fabry-Perot cavities

Whispering-gallery Optical Microprobe for Photoacoustic Imaging

Tunable high-finesse fiber optic Fabry-Perot interferometer for photoacoustic tomography (Conference Presentation)