Abstract:The confinement boundaries of spent nuclear fuel (SNF) canisters are typically fusion welded. Welded microstructures, strain hardening, and residual stresses combined with a chemically aggressive, chloride-rich environment led to concerns that the welded canister may be susceptible to chloride-induced stress corrosion cracking (CISCC). A comprehensive understanding of the modification of stainless steel (SS) metallurgical and mechanical properties by fusion welding could accelerate the predictive analysis of CISCC susceptibility. This paper describes a submerged arc welding (SAW) procedure that was developed and qualified on 12.7 mm (0.5 in.) thick AISI 304/304L SS to produce joints in a way similar to actual SNF canister manufacturing. This procedure has the potential to reduce the production cost and weld CISCC susceptibility by using fewer welding passes and lower heat input than current industrial applications. Global and local mechanical behaviors and properties, as well as residual stress distributions on the welded joint, were studied. The results indicate that hardness values in the fusion zone (FZ) and heat-affected zone (HAZ) are slightly higher than that of the base metal. Strain localization was presented in the HAZ before the tensile stress reached its maximum value, and then it shifted to the FZ. The specimen finally broke in the FZ. High tensile residual stresses exhibited in the FZ and the nearby HAZ suggest the highest CISCC-susceptible spots. The maximum tensile residual stresses were along the welding direction, indicating that if cracks occur, they would be perpendicular to the welding direction. This study involved developing and qualifying a SAW procedure for SNF canister production. The new procedure yielded cost savings (SAW working efficiency increased by about 80%), improved mechanical properties, and presented moderate residual stresses. Analysis revealed that the welded joint's low-stress and high-stress damage assessments may be affected by shifts in the strain localization spot under loading.

Wet corrosion of incinerators under chloride deposits: insights from experimental study on stainless steels and nickel-based alloy weldments

Effect of complex municipal solid waste incineration flue gas on the corrosion of various alloys at 550 °C

High-temperature corrosion-resistant alloy for waste-to-energy plants: Alloy designing, fabrication, and possible corrosion-resistance mechanism

Influence of Post-Welding Heat Treatment on the Corrosion Behavior of a 2050-T3 Aluminum-Copper-Lithium Alloy Friction Stir Welding Joint

Electrochemical corrosion of multiphase stainless steel-based alloy nuclear waste forms

High temperature corrosion mechanism of Ni-5W-6B-28Cr-13Al alloy in simulated MSW incineration environment

High Temperature Corrosion Resistance of Different Commercial Alloys Under Various Corrosive Environments

Microstructural evaluation and corrosion behaviour of Inconel 82 and Inconel 625 overlays on 304L stainless steel weld used in nuclear fuel reprocessing plant

Corrosion studies using potentiodynamic and EIS electrochemical techniques of welded lean duplex stainless steel UNS S82441

Corrosion Behavior of the GH3535 and C276 Alloys at the Liquid/Gas LiCl–KCl Salt Interface at 550 °C

Corrosion behavior of austenitic stainless steel and nickel-based welded joints in underwater wet welding

Hydrothermal Corrosion of Latest Generation of FeCrAl Alloys for Nuclear Fuel Cladding

Metallic impurities induced corrosion of a Ni-26W-6Cr alloy in molten fluoride salts at 850 oC

Chloride-Induced Stress Corrosion Cracking of Friction Stir-Welded 304L Stainless Steel: Effect of Microstructure and Temperature

Corrosion Behavior of Ferritic 12Cr ODS and Martensitic X46Cr13 Steels in Nitric Acid and Sodium Chloride Solutions

Understanding the Effect of Corrosion Resistance in Welded AA2198‐T8 Alloy: Microstructural‐Electrochemical Insights

Corrosion characteristics of Fe, Ni and Ti based alloys near the critical point of water and during supercritical water gasification and oxidation of municipal sludge

Corrosion of 316L exposed to highly concentrated borated water used as shield in nuclear fusion experimental reactors cooling circuits

Study of Mechanical Properties, Microstructure, and Residual Stresses of AISI 304/304L Stainless Steel Submerged Arc Weld for Spent Fuel Dry Storage Systems

Overview of anaerobic corrosion of carbon steel radioactive waste packages in alkaline media in support of the Belgian supercontainer concept

Microstructures and Corrosion/Localised Corrosion of Stainless Steels, Incoloy and Their Weldments in Nitrite-Containing Chloride Environments