Abstract:Laser drilling is always accompanied by recast layers, micro-cracks, and heat-affected zones, which limit its application in engineering. Due to its unique advantages, such as no heat-affected zones, no residual stresses, and no dependence on the mechanical properties of the materials, electrochemical dissolution has been adopted to remove the laser drilling-induced surface defects. The electrochemical dissolution characteristics and surface evolution of the laser-drilled Ni-based superalloys were studied. The polarization curves and electrochemical impedance spectroscopy (EIS) of the laser-drilled materials and the substrate were measured, indicating that the laser-drilled surface had a smaller corrosion resistance than the original substrate. X-ray photoelectron spectroscopy (XPS) results showed that the laser-drilled surface had a much higher oxygen content than the substrate. Additionally, electric current efficiency curves were obtained to study the anodic dissolution behavior of Ni-based superalloys. An electric current density in the 5–40 A/cm2 range was preferred to enhance the electrochemical dissolution rate. Moreover, the effects of electric current densities and post-processing time on the surface roughness and the recast layer thickness of the laser-processed Ni-based superalloys were investigated using a NaCl and NaNO3 solution electrolyte. The evolution of the surface quality and recast layer thickness were clarified. Furthermore, an anodic dissolution model of the laser-processed surface was established to illustrate the electrochemical post-processing mechanisms. Results revealed that electrochemical dissolution could completely remove the laser drilling-induced surface defects in 20 s using a 12.5 wt.% NaNO3 solution electrolyte and a 40 A/cm2 electric current density. Finally, an electrochemical post-processed surface with surface roughness (Ra) of 1.7 µm and without a recast layer was achieved. Micro holes without recast layers and Ra of 0.69 µm were obtained with high efficiency using laser processing and electrochemical post-processing.

Picosecond laser remelting of electrodeposited Ni P coating: Parameters optimization and electrochemical corrosion behavior

Corrosion Resistance Improvement of Ni-P Coatings: Surface Cracks with Different Temperatures Repaired by Laser Remelting

Effect of Laser Spot Overlap on the Mechanical Properties and Corrosion Resistance of Laser-Assisted Electrodeposited Ni-based Coatings

Improvement of Electrochemical deposition Performance and Design of Fe–Ni Multilayer Structure by Nanosecond Laser

A study on the formation conditions of amorphous nickel-phosphorus (Ni-P) alloy by laser-assisted electrodeposition

High temperature oxidation resistance of arc ion plating NiCoCrAlY coating modified via laser shock peening

Effect of Laser Single Pulse Energy on Micro-structural, Mechanical and Corrosion Properties of Amorphous Ni-Fe-P Alloy Prepared by Laser-Assisted Electrodeposition

Study on anodic dissolution behavior and surface evolution of laser-drilled Ni-based superalloys during electrochemical post-processing

An Investigation of the Surface Quality and Corrosion Resistance of Laser Remelted and Extreme High-Speed Laser Cladded Ni-based Alloy Coating

Improvement of Ni–Cr–Mo Coating Performance by Laser Cladding Combined Re-Melting

Study of Nanometer Al2o3 Composite Electroless Deposit Strengthened by Different Laser Power

Enhance corrosion resistance of 304 stainless steel using nanosecond pulsed laser surface processing

Laser Remelting of Plasma Sprayed Nicraly and Nicraly-Al2o3 Coatings

A study on the thermal cyclic behavior of NiCrAlY coatings via femtosecond laser remelting with high repetition rate

Anti-corrosion superhydrophobic surface of LPBF- NiTi alloy fabricated by nanosecond laser machining

Laser Remelting of Plasma Sprayed Coatings

Hot corrosion behavior of NiCoCrAlYSi laser cladding coating modified using high-current pulsed electron beam in different corrosive salt environments

Enhanced corrosion performance of S136 steel after nanosecond pulsed laser polishing

Corrosion Behavior of NiTi Alloys Fabricate by Selective Laser Melting Subjected to Femtosecond Laser Shock Peening

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Investigation on the effect of laser remelting for laser cladding nickel based alloy