Abstract:In order to fabricate large-area PVSCs, one of the critical challenges is to understand the infl uence of ambient environment on resultant perovskite thin-fi lms since perovskite crystals are sensitive to humidity under ambient condition. It has been shown that perovskite crystals degrade gradually when they are in contact with ambient moisture for certain time. [ 31,32 ] Therefore, most of the high performance perovskite solar cells are prepared in glovebox to avoid contacting moisture. However, fabricating PVSCs under ambient condition is inevitable if we desire to transition from laboratory research into large-scale applications. Lately, there are several encouraging reports about allowing limited amount of moisture to facilitate the perovskite crystallization and improve the performance of resulting device. [ 33,34 ] However, there are no detailed underlying mechanisms explained on how moisture affects perovskite crystallization so far. To alleviate these problems, we have investigated the feasibility of achieving fully printable PVSCs by the blade-coating technique under the ambient condition. The blade-coating fabrication has been widely used to fabricate OSCs and is proven to be a simple, environment-friendly, and low-cost method for the solution-processed photovoltaic. Compared to the screen printing, it not only can print nanoparticles, but also can print all kinds of solutions with any concentration. Moreover, the fi lm morphology control of the blade-coating method is much better than the spray coating and roll-to-roll printing; high-quality photoactive layers with controllable thickness can be accomplished by using a precisely translational blade under the ambient condition with controlled relative humidity. The PVSCs with a confi guration of ITO/poly(3,4-ethylenedioxy-thiophene):poly(4-styrenesulfonate) (PEDOT:PSS)/ CH 3 NH 3 PbI X Cl 3− X /[6,6]-phenyl-C 61 butyric acid methyl ester (PC 61 BM)/Bis-C 60 /Ag were fabricated to realize the fully printable process, as illustrated in Figure 1 a. All constituent interlayers, except for the Ag top electrode, were prepared via blade-coating. The coating conditions were optimized to allow the preparation of high-quality interlayer fi lms. Especially, the effect of humidity was carefully investigated and monitored to facilitate the crystallization of perovskite fi lms under ambient condition. Finally, high PCE (10.44% ± 0.23%) device could be achieved after optimizing the blade-coating process and relative humidity in environment. Moreover, a high-performance fl exible PVSC with a PCE of 7.14% ± 0.31% was demonstrated for the fi rst time using this low-temperature (<150 °C) fully printable process. The exceptional photovoltaic properties demonstrated recently for organic–inorganic halide perovskites (such as CH 3 NH 3 PbX 3 (X = Cl, Br, or I)) have attracted great attention from researchers. [ 1–8 ] The promising features of these perovskites include broad and intense absorption spectra, [ 9 ] appropriate semiconducting properties, [ 10 ] long carrier diffusion length, [ 11,12 ]

Scalable Large Area Perovskite Solar Cell Modules Fabricated with High Humidity Tolerance by Vacuum Deposition

Printing High‐Efficiency Perovskite Solar Cells in High‐Humidity Ambient Environment—An In Situ Guided Investigation

Preparation and Optoelectronic Characteristics of Perovskite Module Devices in Air Assisted by Polymer Inner Packaging Layern

Scalable Fabrication of High‐Performance Perovskite Solar Cell Modules by Mediated Vapor Deposition

Highly efficient perovskite solar cells fabricated under a 70% relative humidity atmosphere

Additive-Regulated One-Step Dynamic Spin-Coating for Fabricating High-Performance Perovskite Solar Cells under High Humidity Conditions

In Air High-Efficiency and Stable Perovskite Solar Cells Module Assisted by Polymer Internal Encapsulation

Combined Vacuum Evaporation and Solution Process for High‐Efficiency Large‐Area Perovskite Solar Cells with Exceptional Reproducibility

High-performance quasi-2D perovskite solar cells with power conversion efficiency over 20% fabricated in humidity-controlled ambient air

High‐Performance Thickness Insensitive Perovskite Solar Cells with Enhanced Moisture Stability

A facile strategy for highly efficient perovskite crystals fabricated in a high moisture environment via solvent engineering process

Low Temperature Method-Based Evaporation/spray-Coating Technology for Wide Bandgap Perovskite Solar Cells

Thermal Radiation Driven Ultrafast Crystallization of Perovskite Films Under Heavy Humidity for Efficient Inverted Solar Cells

Preparation of Perovskite Solar Cells in the Air: Degradation Mechanism and Prospects on Large‐area Fabrication

Dual‐doping Strategy of Metal Chlorides in Ambient Air with High Humidity for Achieving Highly Air‐Stable All‐inorganic Perovskite Solar Cells

Vapor-Assisted Crystallization Control Toward High Performance Perovskite Photovoltaics With Over 18% Efficiency In The Ambient Atmosphere

Hydrophobic Hole-Transporting Layer Induced Porous Pbi2 Film for Stable and Efficient Perovskite Solar Cells in 50% Humidity

High efficiency of 19% for stable perovskite solar cells fabrication under ambient environment using “conductive polymer adhesive”

High‐Performance Fully Printable Perovskite Solar Cells via Blade‐Coating Technique under the Ambient Condition

Achieving Efficient and Stable Perovskite Solar Cells in Ambient Air Through Non‐Halide Engineering

Humidity-insensitive Fabrication of Efficient Perovskite Solar Cells in Ambient Air