Abstract:Organic–inorganic hybrid perovskite solar cells (PSCs) are presently gaining significant attention owing to their high conversion efficiencies achieved in recent years. However, poor long-term stability against water and defects at film surfaces and grain boundaries are important factors causing performance degradation and rapid loss of the photovoltaic response. To remedy this, a pyridine derivative with long C–F chains (PFAD) is synthesized and employed as a passivator to reduce the trap states of perovskite and promote better humidity stability via antisolvent properties. The results demonstrate that the trap states of perovskite could be minimized by the presence of pyridinic nitrogen and then the formation of coordination bonds with undercoordinated Pb2+ ions. The resulting carrier recombination time is prolonged and verified via photoluminescence. The power conversion efficiency (PCE) of the PFAD-passivated perovskite solar cell increased to 20.48%, with practical elimination of hysteresis due to the high quality of the perovskite films. The significant gain generated via PFAD modification supports further applications in thin-film optoelectronic devices. Moreover, PFAD-modified devices exhibit enhanced humidity stability due to the protection of hydrophobic C–F chains from moisture; the PCE decreased about 15% after 30 days of exposure in a moisture ambient condition. Our work provides a promising strategy to further improve the performance and stability of perovskite solar cells by designing bifunctional organic molecules with passivation and hydrophobic effects.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01295.XPS spectra of perovskite and PFAD-modified perovskite; XRD patterns of perovskite films at different PFAD concentrations; J–V curves and PCE distributions of the control and PFAD-modified perovskite solar cells; and performance of perovskite solar cells at different PFAD concentrations (PDF)This article has not yet been cited by other publications.

High efficiency of 19% for stable perovskite solar cells fabrication under ambient environment using “conductive polymer adhesive”

Simple Method of Dual Passivation with Efficiency Beyond 20% for Fabricating Perovskite Solar Cells in the Full Ambient Air

Passivation of perovskite surfaces using 2-hydroxyacetophenone to fabricate solar cells with over 20.7% efficiency under air environment

Achieving Efficient and Stable Perovskite Solar Cells in Ambient Air Through Non‐Halide Engineering

Highly Efficient and Stable Perovskite Solar Cells via Modification of Energy Levels at the Perovskite/Carbon Electrode Interface

A facile strategy for highly efficient perovskite crystals fabricated in a high moisture environment via solvent engineering process

Simultaneously Enhancing the Efficiency and Stability of Perovskite Solar Cells by Using P3HT/PEDOT:PSS as a Double Hole Transport Layer

Stitching Perovskite Grains with Perhydropoly(silazane) Anti‐template‐agent for High‐efficiency and Stable Solar Cells Fabricated in Ambient Air

Surface Passivation with a Fluorocarbon-Based Pyridine Derivative for High-Crystallinity Perovskite Solar Cells with Efficiency Over 20% and Good Humidity Stability

Highly efficient perovskite solar cells fabricated under a 70% relative humidity atmosphere

Anti‐Solvent‐Free Fabrication of Stable FA0.9Cs0.1PbI3 Perovskite Solar Cells with Efficiency Exceeding 24.0% through a Naphthalene‐Based Passivator

High Performance Planar Perovskite Solar Cells Based on CH3NH3PbI3-x(SCN)x Perovskite Film and SnO2 Electron Transport Layer Prepared in Ambient Air with 70% Humility

Interfacial Dipole Poly(2-ethyl-2-oxazoline) Modification Triggers Simultaneous Band Alignment and Passivation for Air-Stable Perovskite Solar Cells

Tailoring Defect Passivation for Efficient and Stable Perovskite Solar Cells via an Ionic Liquid Additive

Efficient and stable perovskite solar cells fabrication in open air through adopting a dye interlayer

Efficient and stable perovskite solar cells based on insulating polymer modified ZnO nanoparticles

Fabrication of perovskite solar cells in ambient air by blocking perovskite hydration with guanabenz acetate salt

Printing High‐Efficiency Perovskite Solar Cells in High‐Humidity Ambient Environment—An In Situ Guided Investigation

Tailoring Precursor Chemistry Enabled Room Temperature‐Processed Perovskite Films in Ambient Air for Efficient and Stable Solar Cells with Improved Reproducibility

The poly(styrene-co-acrylonitrile) polymer assisted preparation of high-performance inverted perovskite solar cells with efficiency exceeding 22%

Air-processed and Mixed-Cation Single Crystal Engineering-Based Perovskite Films for Efficient and Air-Stable Perovskite Solar Cells