Abstract:Organic–inorganic hybrid perovskite solar cells (PSCs) are presently gaining significant attention owing to their high conversion efficiencies achieved in recent years. However, poor long-term stability against water and defects at film surfaces and grain boundaries are important factors causing performance degradation and rapid loss of the photovoltaic response. To remedy this, a pyridine derivative with long C–F chains (PFAD) is synthesized and employed as a passivator to reduce the trap states of perovskite and promote better humidity stability via antisolvent properties. The results demonstrate that the trap states of perovskite could be minimized by the presence of pyridinic nitrogen and then the formation of coordination bonds with undercoordinated Pb2+ ions. The resulting carrier recombination time is prolonged and verified via photoluminescence. The power conversion efficiency (PCE) of the PFAD-passivated perovskite solar cell increased to 20.48%, with practical elimination of hysteresis due to the high quality of the perovskite films. The significant gain generated via PFAD modification supports further applications in thin-film optoelectronic devices. Moreover, PFAD-modified devices exhibit enhanced humidity stability due to the protection of hydrophobic C–F chains from moisture; the PCE decreased about 15% after 30 days of exposure in a moisture ambient condition. Our work provides a promising strategy to further improve the performance and stability of perovskite solar cells by designing bifunctional organic molecules with passivation and hydrophobic effects.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01295.XPS spectra of perovskite and PFAD-modified perovskite; XRD patterns of perovskite films at different PFAD concentrations; J–V curves and PCE distributions of the control and PFAD-modified perovskite solar cells; and performance of perovskite solar cells at different PFAD concentrations (PDF)This article has not yet been cited by other publications.

Anti‐Solvent‐Free Fabrication of Stable FA0.9Cs0.1PbI3 Perovskite Solar Cells with Efficiency Exceeding 24.0% through a Naphthalene‐Based Passivator

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Stable Surface Contact with Tailored Alkylamine Pyridine Derivatives for High‐Performance Inverted Perovskite Solar Cells

Air‐Processed Perovskite Solar Cells with >25% Efficiency and High Stability Enabled by Crystallization Modulation and Holistic Passivation

Passivation of perovskite surfaces using 2-hydroxyacetophenone to fabricate solar cells with over 20.7% efficiency under air environment

Simple Method of Dual Passivation with Efficiency Beyond 20% for Fabricating Perovskite Solar Cells in the Full Ambient Air

In Situ Dual‐Interface Passivation Strategy Enables The Efficiency of Formamidinium Perovskite Solar Cells Over 25%

24.96%‐Efficiency FACsPbI3 Perovskite Solar Cells Enabled by an Asymmetric 1,3‐Thiazole‐2,4‐Diammonium

Surface Passivation with a Fluorocarbon-Based Pyridine Derivative for High-Crystallinity Perovskite Solar Cells with Efficiency Over 20% and Good Humidity Stability

Co-passivation of perovskite film towards stable and efficient perovskite solar cell

Co‐Solvent Engineering Contributing to Achieve High‐Performance Perovskite Solar Cells and Modules Based on Anti‐Solvent Free Technology

Synergistic Effect of Anti‐solvent and Component Engineering for Effective Passivation to Attain Highly Stable Perovskite Solar Cells

Bridging‐Solvent Strategy for Quasi‐Single‐Crystal Perovskite Films and Stable Solar Cells

Synergistic Effect of Fluorinated Passivator and Hole Transport Dopant Enables Stable Perovskite Solar Cells with an Efficiency Near 24%

Synergetic Excess PbI2 and Reduced Pb Leakage Management Strategy for 24.28% Efficient, Stable and Eco‐Friendly Perovskite Solar Cells

Controllable Heavy n‐type Behaviours in Inverted Perovskite Solar Cells with Non‐Conjugated Passivants

Fabrication of perovskite solar cells with PCE of 21.84% in open air by bottom-up defect passivation and stress releasement

Reducing the Surface Reactivity of Alkyl Ammonium Passivation Molecules Enables Highly Efficient Perovskite Solar Cells

Tailoring Defect Passivation for Efficient and Stable Perovskite Solar Cells via an Ionic Liquid Additive

Synergistic Full‐Scale Defect Passivation Enables High‐Efficiency and Stable Perovskite Solar Cells

Synergetic Regulation of Oriented Crystallization and Interfacial Passivation Enables 19.1% Efficient Wide‐Bandgap Perovskite Solar Cells