Abstract:In this study, a novel perovskite solar cell (PSC) architecture is presented that utilizes an HTL-free configuration with formamide tin iodide (FASnI3) as the active layer and fullerene (C60) as the electron transport layer (ETL), which represents a pioneering approach within the field. The elimination of hole transport layers (HTLs) reduces complexity and cost in PSC heterojunction structures, resulting in a simplified and more cost-effective PSC structure. In this context, an HTL-free tin HC(NH2)2SnI3-based PSC was simulated using the solar cell capacitance simulator (SCAPS) within a one-dimensional framework. Through this approach, the device performance of this novel HTL-free FASnI3-based PSC structure was engineered and evaluated. Key performance parameters, including the open-circuit voltage (Voc), short-circuit current density (Jsc), fill factor (FF), power conversion efficiency (PCE), I-V characteristics, and quantum efficiency (QE), were systematically assessed through the modulation of physical parameters across various layers of the device. A preliminary analysis indicated that the HTL-free configuration exhibited improved I-V characteristics, with a PCE increase of 1.93% over the HTL configuration due to improved electron and hole extraction characteristics, reduced current leakage at the back contact, and reduced trap-induced interfacial recombination. An additional boost to the device's key performance parameters has been achieved through the further optimization of several physical parameters, such as active layer thickness, bulk and interface defects, ETL thickness, carrier concentration, and back-contact materials. For instance, increasing the thickness of the active layer PSC up to 1500 nm revealed enhanced PV performance parameters; however, further increases in thickness have resulted in performance saturation due to an increased rate of hole-electron recombination. Moreover, a comprehensive correlation study has been conducted to determine the optimum thickness and donor doping level for the C60-ETL layer in the range of 10-200 nm and 1012-1019 cm-3, respectively. Optimum device performance was observed at an ETL-C60 ultra-thin thickness of 10 nm and a carrier concentration of 1019 cm-3. To maintain improved PCEs, bulk and interface defects must be less than 1016 cm-3 and 1015 cm-3, respectively. Additional device performance improvement was achieved with a back-contact work function of 5 eV. The optimized HTL-free FASnI3 structure demonstrated exceptional photovoltaic performance with a PCE of 19.63%, Voc of 0.87 V, Jsc of 27.86 mA/cm2, and FF of 81%. These findings highlight the potential for highly efficient photovoltaic (PV) technology solutions based on lead-free perovskite solar cell (PSC) structures that contribute to environmental remediation and cost-effectiveness.

Optimizing Lead-free MASnBr 3 Perovskite Solar Cells for High-Efficiency and Long-Term Stability Using Graphene and Advanced Interface Layers

Enhancing photovoltaic efficiency: Integrating graphene and advanced interface layers to reduce the recombination losses in lead-free MASnI 3 perovskite solar cells

Utilizing Density Functional Theory and SCAPS Simulations for Modeling High‐Performance MASnI3‐Based Perovskite Solar Cells

Design and performance optimization of a novel tri-layer unleaded all inorganic lead-free mixed halide CsSnI 3-x Br x heterojunction solar cell

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Optimizing the performance of perovskite-based organic solar cells via graphene integration as the hole transport layer: a comprehensive analysis

Exploring eco-friendly novel charge transport materials for enhanced performance of tin based perovskite solar cell

Design and optimization of high-performance eco-friendly perovskite solar cells: Utilizing FAMASnGeI3 and CsGeI3 as absorbers and tuning HTL and interface parameters

Device modeling of high performance and eco-friendly FAMASnI 3 based perovskite solar cell

Current Status of Pb-free PSCs and Infer the Highest Achievable PCE Via Numerical Modeling, and Optimization of Novel Structure FAMASnGeI3 Based PSCs

Development of low-cost and high-efficiency solar modules based on perovskite solar cells for large-scale applications

Evaluating the influence of novel charge transport materials on the photovoltaic properties of MASnI3 solar cells through SCAPS-1D modelling

Advanced Optoelectronic Modeling and Optimization of HTL-Free FASnI3/C60 Perovskite Solar Cell Architecture for Superior Performance

Enhancing power conversion efficiency of lead-free perovskite solar cells: a numerical simulation approach

Exploring Lead Free Mixed Halide Double Perovskites Solar Cell

A Novel Conductive Mesoporous Layer with a Dynamic Two-Step Deposition Strategy Boosts Efficiency of Perovskite Solar Cells to 20%

Methylammonium and Bromide‐Free Tin‐Based Low Bandgap Perovskite Solar Cells

Optimization of the architecture of lead-free CsSnCl3-perovskite solar cells for enhancement of efficiency: A combination of SCAPS-1D and wxAMPS study

Progress Towards High-Efficiency and Stable Tin-Based Perovskite Solar Cells

Strategic integration of electron transport layer for high-performance optimized lead-free double perovskite solar cells with temperature dependence

Breakthrough in sustainable photovoltaics:Achieving 30.86 % efficiency with innovative lead-free bilayer perovskite solar cells using SCAPS-1D and DFT framework