Abstract:Fouling control strategies play a crucial role in membrane distillation (MD) process, primarily due to the significant limitation of fouling during the scaling-up process. The utilization of microbubbles (MBs) aeration has exhibited promising potential in mitigating membrane fouling when treating high salinity wastewater. Aeration can introduce gas-liquid two-phase flow on the membrane surface, thereby increasing the membrane surface shear force. The mechanism of aeration technology for controlling fouling includes the following points: introduction of gas-liquid two-phase flow; physical substitution of concentration polarization layer; pressure pulses caused by bubbles flowing through the membrane surface and increasement of the cross flow velocity. This research aims to optimizing the effect of air MBs with different concentrations and sizes introduced in the feed side on membrane fouling control, we creatively used the method of releasing pressure gradiently to achieve size regulation of MBs within a certain range for the first time, firstly regulated the generation of MBs by manipulating gas flow rate and release pressure. Under the optimal condition of 40 mL/min and 0.6 MPa, it will yield concentration of 1.58 × 10 4 /mL and D50 Sauter size of 64.69 μm MBs with pure water permeance flux of 12.32 kg/(m 2 ·h). It was observed that higher gas flow rates primarily increased MBs concentration, while lower pressures predominantly reduced MBs size through the method of inline imaging. Experimental results indicated that introduction of MBs can slightly improve the temperature polarization coefficient and mass transfer coefficient under different operating modes. Consequently, further investigations focused on the influence of MBs characteristics on different fouling control. All conditions reach 99 % rejection for inorganic salt and HA. This study provided empirical evidence that higher concentration and larger size of MBs intensify the gas-liquid two-phase flow disruption and exhibit a better shear effect on scaling phenomena, which yield advantageous outcomes in terms of augmenting permeance flux and water vapor production, with permeance flux increased from 40.12 % to 55.42 % for inorganic fouling and increased from 68.35 % to 80.15 % for inorganic and HA fouling. These results were confirmed via membrane surface using scanning electron microscopy and energy dispersive spectroscopy. In summary, this research aided in identifying appropriate operating conditions for mitigating inorganic and composite scaling by implementing air-infused MBs in direct contact membrane distillation (DCMD), which provides scientific and technical guidance for controlling fouling in MD in practical applications.

Impacts of micron-sized aeration bubble on sludge properties and hydraulic dynamics in relation to membrane fouling alleviation

Sludge rheological and physiological characteristics in a pilot-scale submerged membrane bioreactor

Effective Control of Membrane Fouling by Filamentous Bacteria in a Submerged Membrane Bioreactor

Influence of Aeration on Microbial Polymers and Membrane Fouling in Submerged Membrane Bioreactors

Sludge reduction and process performance in a submerged membrane bioreactor with aquatic worms

Optimizing fouling mitigation in membrane distillation by controlled microbubble size and concentration

Study on the impact of sludge components on membrane fouling in a sub-merged membrane bioreactor

New Insights into Membrane Fouling in Submerged Membrane Bioreactor Based on Rheology and Hydrodynamics Concepts

Effect of Aeration Intensity on Operating Characteristics of Membrane Bioreactors

Optimizing slug bubble size for application of the ultra-thin flat sheet membranes in MBR: a comprehensive study combining CFD simulation and experiment

Enhanced Anaerobic Digestion Performance and Sludge Filterability by Membrane Microaeration for Anaerobic Membrane Bioreactor Application

A Comprehensive Study on Membrane Fouling in Submerged Membrane Bioreactors Operated under Different Aeration Intensities

Effect of Micro and Nanobubble Size and Concentration on Membrane Fouling: Strategies for Energy-Saving and Ultrafiltration Efficiency Enhancement

Effect of Aeration on Characteristics of the Activated Sludge and Membrane Fouling in a Submerged Membrane Bioreactor

Impact of Biological Constituents and Properties of Activated Sludge on Membrane Fouling in a Novel Submerged Membrane Bioreactor

Experimental Research on Mechanism of Membrane Fouling in a Submerged Membrane Bioreactor

Superior performance of a membrane bioreactor through innovative in-situ aeration and structural optimization using computational fluid dynamics

Employing Low Dissolved Oxygen Strategy to Simultaneously Improve Nutrient Removal, Mitigate Membrane Fouling, and Reduce Energy Consumption in an AAO-MBR System: Fine Bubble or Coarse Bubble?

Hydrodynamic effect on sludge accumulation over membrane surfaces in a submerged membrane bioreactor

Transition of fouling characteristics after development of membrane wetting in membrane-aerated biofilm reactors (MABRs)

Effects of Aeration Parameters on Effluent Quality and Membrane Fouling in a Submerged Membrane Bioreactor Using Box–Behnken Response Surface Methodology