Abstract:Wear due to sliding is an inevitable problem in many engineering applications. Protective surface coating is usually used to mitigate this problem. The development in this field is continuous and consistent. There are many types of coatings according to their compositions and the deposition methods. One of the coatings with the most promising properties, such as the hardness, is the Diamond-Like Carbon (DLC) coating. The tribological properties of this coating generated by Plasma-Assisted Chemical Vapor Deposition (PACVD) and applied on bearing steel 52100 ASTM are not available. In this study, the wear resistance of the DLC coating applied to bearing steel 52100 ASTM, was evaluated. The coating method employed was PACVD, which is regarded as one of the most distinctive coating techniques due to the unique tribological properties imparted to the coating. The pin-on-disc tribometer was used to examine the coefficient of friction and mass losses for samples of (steel disc against steel ball) and (DLC coated disc against DLC coated ball) under constant sliding velocity and constant sliding distance with four different loads (2, 5, 10 and 20 N) that results in maximum contact pressure below and higher than the maximum shear stress of the bearing steel. The wear coefficient was calculated using Archard's equation based on the experimental results. It was found that the DLC coating may result in significant reduction, reaching 93.5%, in weight loss and 83% in COF at low contact pressure (less than the maximum shear stress). However, at high contact pressure (equals to or higher than the maximum shear stress) the weight loss and the COF for the DLC coating are higher than those of the bearing steel. This behavior indicates that the DLC coated pair may not be suitable at high loads. The wear coefficient is calculated for each testing condition and it is found to be affected by the applied load. The average wear coefficient for the DLC coating is provided which can be used with the Archared wear model to predict the wear rate within the range of the parameters used in this study.

Enhancing tribological performance of high‐density polyethylene polymer with diamond‐like carbon coating and mollusk shells filler

Tribological Properties of Diamond-Like Carbon Films Deposited by Vacuum Arc

Tribological study of lubricious DLC biocompatible coatings

Preliminary tribological evaluation of nanostructured diamond coatings against ultra-high molecular weight polyethylene

Comparison Of Tribological Performances Of High Density Polyethylene Enhanced With Carbon Nanofibers

The effect of diamond like carbon coating on the wear resistance at dry sliding conditions

Fabrication and characterization of DLC coated microdimples on hip prosthesis heads

Mechanical and Biological Characteristics of Diamond-Like Carbon Coated Poly Aryl-Ether-ether-ketone.

Enhancing the Tribological Properties of Low-Density Polyethylene Using Hard Carbon Microfillers

Synergistic tribological effect between polyisobutylene succinimide-modified molybdenum oxide nanoparticle and zinc dialkyldithiophosphate for reducing friction and wear of diamond-like carbon coating under boundary lubrication

Mechanical Properties, Tribological Behavior, and Biocompatibility of High-Density Polyethylene/carbon Nanofibers Nanocomposites

An Investigation of the Bio-tribological Performance of Diamond-like Carbon/Ultrahigh Molecular Weight Polyethylene Couple.

Influence of 1-Ethyl-3-methylimidazolium Diethylphosphate Ionic Liquid on the Performance of Eu- and Gd-Doped Diamond-like Carbon Coatings

Formulation and selection of composite biomaterials for acetabular cup of hip prosthesis with wear analysis

Feasibility of using diamond-like carbon films in total joint replacements: a review

Designing hydrogen-free diamond like multilayer carbon coatings for superior mechanical and tribological performance

Ti3C2Tx‐UHMWPE Nanocomposites—Towards an Enhanced Wear‐Resistance of Biomedical Implants

In Vitro and In Vivo Evaluation of Toxicity of Structurally Different Diamond-Like Carbon Wear Debris in Joint Replacements

Optimization through combined compromise solution and weight determination through SHANNON-ENTROPY for multi criteria decision making in tribological testing of ultrahigh molecular weight polyethylene nano-composite in SBF environment and compression testing with it's invitro analysis

Enhancement of tribological properties by dynamic mixing of diamond-like carbon/Mo films on steel

Effect of Lubricant Formulations on the Tribological Performance of Self-Mated Doped DLC Contacts: a review