Abstract:This research examines the potential of a synthetic e-diesel and oxymethylene dimethyl ether blend in a heavy-duty single-cylinder engine. The main purpose is to find the optimal engine settings that maximize engine efficiency and minimize emissions. As the first step, a methodology was developed and applied to simplify the engine's map into five characteristic points to be representative of the World Harmonized Transient Cycle, assigning weights to each load region. This simplification reported low error estimations for fuel consumption and NOx emissions over the cycle. After obtaining the five points, a drop-in analysis was assessed, where the fuel was evaluated with the same settings as diesel, revealing more advanced and shorter combustion with great reductions in soot emissions. Then, a group of three air management and three injection parameters was selected for optimization. A novel methodology combining Taguchi Design and Response Surface Methodology is developed and applied to find the best engine settings. By integrating these two methods, the research reduced the number of required experiments if only one method were used and maintained the goal of achieving higher thermal efficiencies with the new fuel blend compared to the diesel baseline. Significant statistical results were obtained in the Taguchi design, revealing the air management factors that most affected the responses; meanwhile, second-order models with high accuracy helped in finding the best injection parameters. Subsequently, the best settings were experimentally evaluated, and optimal conditions determined by the two methods were validated, confirming the effectiveness of the methodology. Optimization results revealed an improvement of around 2% higher efficiencies for the five tested points while achieving important average reductions of 28% less in NOx with additional decreases in CO, HC, and soot levels, all outperforming traditional diesel benchmarks. Finally, a well-to-wheel analysis using the simplified cycle confirmed a substantial reduction in carbon impact when replacing diesel with this alternative fuel. The successful application of this methodology to recalibrate an engine with an alternative fuel blend shows the potential of using these fuels in existing engines and offers a novel methodology that can be escalated and applied under the engine calibration context.

Multi-objective optimization of the performance and emissions characteristics of a CI engine powered by Pyrus glabra biodiesel as a novel feedstock using response surface method

A Taguchi-based hybrid multi-criteria decision-making approach for optimization of performance characteristics of diesel engine fuelled with blends of biodiesel-diesel and cerium oxide nano-additive

The Influence of Diesel–Ethanol Fuel Blends on Performance Parameters and Exhaust Emissions: Experimental Investigation and Multi-Objective Optimization of a Diesel Engine

Multi-objective RSM-based optimization of diesel-diethyl ether blends in diesel engine to achieve sustainable development goals

Multi-objective optimization of ternary blends of Algal biodiesel-diesel-1-decanol to mitigate environmental pollution in powering a diesel engine using RSM, ANOVA, and artificial bee colony

Computational Modeling and Multi-objective Optimization of Engine Performance with Waste Soya Oil-Based Biodiesel Using Genetic Algorithm and Utility Function

Multiple response optimizations to improve performance and reduce emissions of Argemone Mexicana biodiesel-diesel blends in a VCR engine

Performance and emission characteristics of novel biodiesel-diesel blends: an RSM and ANN approach

Comparative thermal assessment and emission analysis of various green biodiesel from novel feedstocks for CI engines: a sustainable approach towards emission reduction

The improvements of combustion and emission for a diesel-biodiesel hybrid engines based on response surface methodology

Assessment of performance and emission characteristics of CI engine using tyre pyrolysis oil and biodiesel blends by nano additives: An experimental study

Combustion exhaust release impact, diesel engine performance, and optimization studies of green diesel-petrodiesel blend in a high compression ratio direct-injection compression-ignition engine

Prediction of emissions and performance of a gasoline engine running with fusel oil–gasoline blends using response surface methodology

Performance optimization of a diesel engine fueled with hydrogen/biodiesel with water addition based on the response surface methodology

Overall Performance Investigation and Optimization of a Multi-fuel Operated Compression Ignition Engine Using Coupled Taguchi and Grey Relational Analysis

Performance analysis and optimization of thermal barrier coated piston diesel engine fuelled with biodiesel using RSM

Effective utilization of tobacco (Nicotiana Tabaccum) for biodiesel production and its application on diesel engine using response surface methodology approach

Optimization of biodiesel production parameters for hybrid oil using RSM and ANN technique and its effect on engine performance, combustion, and emission characteristics

Optimization methodology combining Taguchi design and response surface method to maximize a compression ignition engine efficiency fueled with oxygenated synthetic fuel

Optimization of engine performance, emission and combustion parameters by using mixed nonedible oil biodiesel with nano-additives using hybrid techniques

Performance of diesel engine running on diesel fuel and its blends with refined biomass fast pyrolysis bio-oil