Abstract:Abstract. Bentonite buffer in a geological repository will be simultaneously heated from decaying radioactive waste and hydrated from the surrounding host rock, triggering complex and coupled THMC (thermal–hydrological–mechanical–chemical) processes. Understanding the THMC behavior of bentonite-based engineered barrier system (EBS) is key to the evaluation and prediction of its long-term performance. Studies on the THMC process have been focused on conditions under 100 ∘C, as most design concepts impose a thermal limit of 100 ∘C in bentonite. Recently, studies under high-temperature conditions have been conducted to evaluate the possibility of raising the thermal limit and expanding the data/knowledge base to increase the confidence level. In this abstract, we present a series of bench-scale laboratory experiments at high temperatures (up to 200 ∘C) and the corresponding modeling work. Two sets of column tests were conducted, and each set consisted of two test columns: a control column undergoing only hydration (non-heated) and an experiment column experiencing both heating and hydration (heated). During the experiment, frequent X-ray computed tomography (CT) images were collected to provide a 3D visualization of the density distribution and present the spatiotemporal evolution of (1) hydration/dehydration, (2) clay swelling/shrinkage, (3) displacement, and (4) mineral precipitation. The two sets of tests differ with respect to several experimental conditions, such as bentonite type, compacted density and water content, water chemistry, and hydration pressure, but the important difference is that the first set used bentonite powder with a dry density of 1.28 g cm−3, whereas the second set used granulated bentonite (mixture of pellets and powder) with a dry density of 1.45–1.5 g cm−3. In both sets of experiments, a comprehensive post-dismantling characterization of bentonite samples was carried out after the column tests had been running for 1.5 years. Comparing non-heated and heated columns, the temperature gradient led to lower degree of homogenization of bentonite after bentonite became fully saturated; comparing the first and second sets, granulated and powdered bentonite exhibited drastically different hydration behavior. A THM model with a 2D axisymmetric grid system was used to interpret the data from the first set of tests. The model considers the combined impact of saturation, fluid pressure, and porosity change due to swelling/compression on the spatiotemporal distribution of bulk density and movement of the thermocouple modules. Observations from the tests help us understand the early perturbation of bentonite buffer under high temperature, and data from these tests improve the calibration of key constitutive hydrological and mechanical models and, therefore, enhance the modeling capability with respect to calculating the long-term evolution of bentonite buffer.

Volume Deformation and Hydraulic Conductivity Behavior of Sand-Bentonite Mixtures with Fiberglass Additives under High Temperatures

Experimental Study on Thermal Conductivity of Mixed Materials of Sand and Bentonite

Thermally induced volume change behavior of sand–clay mixtures

Experimental Investigations on Thermo-Hydro-mechanical Properties of Compacted GMZ01 Bentonite-Sand Mixture Using As Buffer Materials

Mechanical Properties and Microstructures of Steel-basalt Hybrid Fibers Reinforced Cement-based Composites Exposed to High Temperatures

The plastic behavior and compression of bentonite clay under heating effect

Influence of Temperature on the Volume Change Behavior of Saturated Sand

Temperature Effects on Unsaturated Hydraulic Property of Bentonite-Sand Buffer Backfilling Mixtures

The impact of high temperature on mechanical properties and behaviors of sandstone

Bentonite buffer under high temperature: laboratory experiments and coupled process modeling

Evaluation of Thermophysical and Mechanical Properties of Sandstone Due to High-Temperature

Thermo-hydro-mechanical Properties of Bentonite-Sand-graphite-polypropylene Fiber Mixtures As Buffer Materials for a High-Level Radioactive Waste Repository

Volume change characteristics of bentonite-sand mixture under hydro-mechanical coupling condition

Coupled Thermo-Hydro-Mechanical Modeling of Bentonite Under High Temperature Heating and Hydration for a Bench-Scale Laboratory Experiment

Experimental Study on Shear Characteristics of Fiber-Reinforced Shotcrete-Rock Interface Under High-and-Variable Temperature

Temperature Effect on the Deformation Behaviour of Compacted Bentonite under Free Swelling/Shrinkage Conditions

Effect of fibers addition on mechanical properties of eco-friendly phosphogypsum-based composite at high temperatures

Thermal impacts on the erosion of compacted bentonite under flow rate

Effects of Temperature and Thermal Cycles on the Elastic Shear Modulus of Saturated Clay

Study on Mechanical Properties of Post-High-Temperature Sandstone

Investigating The Volume Change Characteristics Of Bentonite/Sand Mixture Under Hydro-Mechanical Coupling Condition