Abstract:The advantages of utilizing activated carbonate additions as a surplus provider of calcium were elucidated in this study. The pozzolanic activity inherent in clays and minerals containing carbonate can be tailored through the de‐hydroxylation of clay and the de‐carbonation of calcite content. Special consideration needs to be given to ensuring the effective activation of schist‐type materials, given the potential for substantial variations between the outcomes of laboratory‐scale and industrial‐scale activation processes for materials characterized by very low thermal conductivity, such as schists. Supplementary cementitious materials (SCMs) are partial substitutes for ordinary Portland cement (OPC) to reduce cost, the production of carbon dioxide (CO2), and fossil fuel consumption. Recent studies illustrated the effectiveness of calcined kaolinite clay as a proper partial replacement for OPC. Hence, schist‐type materials containing sufficient clay contents are regarded as promising candidates for OPC replacement. This study focuses on the possible use of activated calcium carbonates (CaCO3) to augment pozzolanic reactions of schists as a substitute for OPC. The use of activated calcium carbonates proved to be successful in expediting pozzolanic reactions and facilitating the formation of additional calcium aluminosilicate hydrate (C‐A‐S‐H). In this study, the optimal strength performance for blended cement was achieved by adjusting the total carbonate content to 30 wt.% of the schist. The decision to introduce carbonate to the schist was guided by calculations determining the need for an excess of calcium ions to fully harness the potential for C‐A‐S‐H formation. Virgin and augmented schists were activated by up to 80% of their respective potentials by heat treatment. Phase content and decomposition behavior of the active components were investigated by thermogravimetric analysis (TGA), x‐ray diffraction (XRD), and scanning electron microscopy (SEM). Cement paste samples incorporating 30 wt.% replacement of OPC with activated schist SCMs were prepared. The phase distribution and compressive strengths of these samples were assessed at hydration intervals of 2, 7, 28, 50, and 90 days. Cement formulations with activated calcium‐augmented SCMs exhibited compressive strength values at 109%, 101%, 96%, 95%, and 94% compared to pure cement paste at 2, 7, 28, 50, and 90 days, respectively. These values surpassed 90% of the compressive strength of pure OPC at equivalent hydration time points.

Hydration of a 2-component CSA-OPC-mix – timing of component blending & setting on demand

Microstructure Refinement of Calcium-Sulfate-aluminate and Portland Cement (CSA-PC) Hybrids with Accelerated CO2 Curing (ACC)

Portland/Sulfoaluminate Cement Blends for the Control of Early Age Hydration and Yield Stress

Factors Influencing the Hydration, Dimensional Stability, and Strength Development of the OPC-CSA-Anhydrite Ternary System

Impact of varying Li2CO3 additions on the hydration of ternary CSA-OPC-anhydrite mixes

Early Hydration Heat of Calcium Sulfoaluminate Cement with Influences of Supplementary Cementitious Materials and Water to Binder Ratio

Early hydration and hardening of OPC-CSA blends for cementitious structure of 3D printing

Rheological behavior of Portland clinker-calcium sulphoaluminate clinker-anhydrite ternary blend

Mix and measure II: joint high-energy laboratory powder diffraction and microtomography for cement hydration studies

Comprehensive evaluation of early-age hydration and compressive strength development in seawater-mixed binary and ternary cementitious systems

Synergistic Effect and Mechanism of Nano-C-S-H Seed and Calcium Sulfoaluminate Cement on the Early Mechanical Properties of Portland Cement

Early Hydration and Viscoelastic Properties of Tricalcium Aluminate Pastes Influenced by Soluble Sodium Salts

Internal hydrophobic treatment for mortar containing supplementary cementitious materials: thermal analysis of kinetics and products of hydration

Microstructural phase evolution and strength development of low-lime calcium silicate cement (CSC) paste incorporating ordinary Portland cement under an accelerated carbonation curing environment

Effects of Accelerators and Retarders in Early Strength Development of Concrete Based on Low-Temperature-Cured Ordinary Portland and Calcium Sulfoaluminate Cement Blends

Autogenous and drying shrinkage of mortars based on Portland and calcium sulfoaluminate cements

Optimization of Ca/Si ratio in schists to enhance the pozzolanic supplementary cementitious material for OPC blending

The Early Hydration of OPC Investigated by In-Situ XRD, Heat Flow Calorimetry, Pore Water Analysis and 1H NMR: Learning about Adsorbed Ions from a Complete Mass Balance Approach

Binding Mechanism of CSA Cement on Premixed [math] and Its Governing Parameters

In situ synchrotron powder diffraction study of LC 3 cement activation at very early ages by C-S-H nucleation seeding

Microstructure refinement of calcium-sulfate-aluminate and portland cement (CSA-PC) hybrids with accelerated CO 2 curing (ACC)