Abstract:In order to study the shear mechanical properties of rock joint under different unloading stress paths, the RDS-200 rock joint shear test system was used to carry out direct shear tests on concrete joint specimens with five different morphologies under the CNL path and different unloading stress paths. The unloading stress paths include unloading normal load and maintaining constant shear load (UNLCSL), unloading normal load and unloading shear load (UNLUSL), unloading normal load and increasing shear load (UNLISL). The results show that the peak shear strength, cohesion, internal friction angle, pre-peak shear stiffness and residual shear strength of concrete joints under CNL path increases with the increasing JRC and normal stress. Under the UNLCSL path, under the same initial shear stress τ 1 , instability normal stress σ i decreases with the increasing JRC , and normal stress unloading amount Δσ n increases with the increasing JRC . Under the same JRC , σ i increases with the increase of τ 1 , and Δσ n decreases with the increasing τ 1 . Under the same JRC and σ i , τ i is significantly smaller under the UNLCSL path than the CNL path. Under the same JRC , the cohesion under the UNLCSL path is less than the CNL path, and the internal friction angle is higher than that the CNL path. Under the same JRC and σ i , τ i is the largest under the path of CNL and UNLISL, followed by the UNLCSL path, and τ i under the UNLUSL path is the smallest. Compared with the CNL path, the variation range of the specimen internal friction angle is within 3% while the average decrease percentage of the specimen cohesion reaches 37.6% under the UNLCSL path, UNLISL, and UNLUSL. Therefore, it can be inferred that the decrease in cohesion caused by normal unloading is the main reason for the decrease in joint instability shear strength. After introducing the correction coefficient k of cohesion to modify the Mohr-Coulomb criterion, the maximum average relative error after correction is only 3.5%, which is significantly improved compared with the maximum average relative error of 56.9% before correction. The research conclusions can provide some reference for the accurate estimation of shear bearing capacity of rock joints under different unloading stress paths, which is of great significance to the stability evaluation and disaster prevention of rock mass engineering.

Study on Shear Strength Characteristics of Basalt-Concrete Bonding Interface Based on in-situ Direct Shear Test

Study on Shear Strength Characteristics of Columnar Jointed Basalt Based on in-situ Direct Shear Test at Baihetan Hydropower Station

Experimental Study on Direct Shear Performance of Concrete-Concrete Interface of Prefabricated Structure Sleeve Grouting Connection

Experimental Study of the Shear Strength of Bonded Concrete–Rock Interfaces: Surface Morphology and Scale Effect

Shear-friction behavior of concrete-to-concrete interface under direct shear load

The Interface Behavior of Rock, Conventional Vibrated and Roller Compacted Concrete

Influence of Concrete–Rock Bonds and Roughness on the Shear Behavior of Concrete–Rock Interfaces under Low Normal Loading, Experimental and Numerical Analysis

Experimental, analytical, and finite element assessment of the shear strength of concrete‐rock interfaces at different scales

Bonding Properties Between Steel-Basalt Hybrid Fibers Reinforced Cementitious Composites and Existing Concrete at High Temperatures

Experimental study of the shear behavior of concrete-rock interfaces under static and dynamic loading in the context of low confinement stress

Effects of roughness on shear properties and acoustic emission characteristics of bonded Rock-Concrete interfaces

Experimental Investigation on Shear Behavior of the Interface between Early-Strength Self-Compacting Shrinkage-Compensating High-Performance Concrete and Ordinary Concrete Substrate

Experimental Study on Shear Strength of Foundation Interface with Inlaying-Fragmentation Structure

Enhancing the interfacial bond performance of engineered cementitious composites and concrete

Assessment of concrete–rock contact shear behaviour based on in situ shear tests

Large-Scale Test Study on the Three-Dimensional Behavior of the Gravel–Concrete Interface of a CFR Dam

The experimental and numerical simulation of interface shear behavior between ECC and coal gangue concrete

Experimental study of shear behavior of rock–shotcrete interface under dynamic shearing: insights from interface roughness and strain rate

Experimental study on shear mechanical properties of concrete joints under different unloading stress paths

Bonding Performance Between Ultra High Toughness Cementitious Composites and Existing Concrete

Study on the Strength Characteristics of Columnar Jointed Basalt with a True Triaxial Apparatus at the Baihetan Hydropower Station