Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Anand constitutive modeling of multilayer Silver-Tin transient liquid phase foils using tensile and creep testing

Experiments, constitutive modeling, and simulations on the creep behavior of the AgSn transient liquid phase metallic bonds

Experimental Determination and Modification of Anand Model Constants for Pb-Free Material 95.5Sn4.0ag0.5cu

Mechanical Properties and Parameter Determination of Anand Viscoplastic Constitutive Model for Pb-free Solder Alloys

Anand Parameter Test for Pb-Free Material SnAgCu and Life Prediction for a CSP

The variation in Anand model parameters – How does that affect the bond's response? A comparative study considering sintered Ag bonds

Experimental Determination of Mechanical Properties for Lead-Free Material SnAgCu

A Combined Loading-Creep Model of ETFE Foils for Flat-Patterning Structures

Modelling of Ag3Sn coarsening and its effect on creep of Sn–Ag eutectics

Constitutive behavior and Anand model of novel lead-free solder Sn-Zn-Bi-In-P

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

Micromechanical modelling of SnAgCu solder joint under cyclic loading: Effect of grain orientation

Anisotropy in creep-aging behavior of Al–Li alloy under different stress levels: experimental and constitutive modeling

Compressive Mechanical Properties and Parameter Determination of Anand Viscoplastic Constitutive Model for a New Lead-free Material Sn-Zn-Bi-In-P

A non-quadratic pressure-sensitive constitutive model under non-associated flow rule with anisotropic hardening: Modeling and validation

Creep Constitutive Relationships And Cyclic Behaviors Of Sn96.5ag3cu0.5 Under High Temperatures

A study on the thermomechanical response of various die attach metallic materials of power electronics

Constitutive modelling of coupled creep deformation and age hardening behavior of aluminum alloys under various thermal and mechanical loadings

A Constitutive Model for Asymmetric Cyclic Hysteresis of Wrought Magnesium Alloys under Variable Amplitude Loading

Creep-fatigue interactions in a polycrystalline structural material under typical high-temperature power plant operating conditions

Constitutive Modeling of Annealed OFHC with Wide Strain-Rate and Temperature Effects: Incorporating Dislocation Dynamics and Normalized Microstructural Size Evolution