Abstract:Al-7Si-Mg alloy castings have extensive applications in automotive industries, and the tensile properties of these alloys including yield strength, ultimate tensile strength and elongation are commonly used to judge their mechanical properties. In this work, the modified precipitation kinetics model, yield strength model and strain hardening model have been proposed to predict the tensile properties of Al-7Si-Mg alloys. The precipitation kinetics model can be used to predict the precipitate microstructure parameters including the precipitate density, size, size distribution, volume fraction, and composition and so on in these alloys, combining which with the strength model, their yield strengths can be obtained. The strain hardening model can be applied to simulate the stress-strain curves during tensile process, and the ultimate tensile strengths and elongations can be obtained by combining this model with the experimental data fitted with the expression (sigma(UTS)-sigma(Y))=m center dot sigma(Y)+n+f(T-ss). First, the evolution of precipitate microstructure parameters and yield strengths as a function of ageing time were simulated, and then their comparisons with the experimental results were performed. The possible reasons resulting in the deviations between simulated and experimental yield strengths were analyzed. The stress-strain curves during tensile process of Al-7Si-0.36Mg alloy were simulated using strain hardening model, and the influences of ageing treatment and as-cast microstructure refining scale on the parameters of dislocation storage rate, dynamic recovery rate and the stress-strain curves were analyzed. Then, the ultimate tensile strengths and elongations of Al-7Si-0.4Mg alloy aged at different temperatures were predicted which are in better agreement with the experimental results, and the influence of secondary dendrite arm spacing on tensile properties was also analyzed. Finally, the limitation of present model and the factors influencing the prediction precision of tensile properties were outlined.

Constitutive modelling of coupled creep deformation and age hardening behavior of aluminum alloys under various thermal and mechanical loadings

Constitutive modeling of mechanical behaviors in gradient nanostructured alloys with hierarchical dual-phased microstructures

Constitutive equations in creep of 7B04 aluminum alloys

A unified constitutive model for multiphase precipitation and multi-stage creep ageing behavior of Al-Li-S4 alloy

Anisotropy in creep-aging behavior of Al–Li alloy under different stress levels: experimental and constitutive modeling

Damage in Creep Aging Process of an Al-Zn-Mg-Cu Alloy: Experiments and Modeling

Experimental investigation and modelling of yield strength and work hardening behaviour of artificially aged Al-Cu-Li alloy

On multiaxial creep–fatigue considering the non-proportional loading effect: Constitutive modeling, deformation mechanism, and life prediction

The Influence of Creep Ageing on the Hardening Behavior and Microstructure of 7050 Aluminum Alloy

Modelling the Effect of Room Temperature Storage and Deformation on the Age-hardening Behaviour of Al-Mg-Si alloys

A Crystal Plasticity-Based Creep Model Considering the Concurrent Evolution of Point Defect, Dislocation, Grain Boundary, and Void

Constitutive Modeling of Annealed OFHC with Wide Strain-Rate and Temperature Effects: Incorporating Dislocation Dynamics and Normalized Microstructural Size Evolution

A new thermodynamically based model for creep and cyclic plasticity

Modeling the Precipitation Kinetics and Tensile Properties in Al-7si-Mg Cast Aluminum Alloys

Creep aging behavior of Al-Cu-Mg-Si alloy with elastic and plastic loads

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy

Modelling the spatial evolution of excess vacancies and its influence on age hardening behaviors in multicomponent aluminium alloys

Experimental and Physical-Based Constitutive Model Study of Fcc Metal over Wide Temperature and Strain Rate Ranges

A New Method to Characterize and Model Stress-Relaxation Aging Behavior of Aluminum Alloys Under Age Forming Conditions

Modeling of Strain Hardening Behavior and Mechanical Properties of Al 7Si Mg Cast Aluminum Alloys During Tensile Process

Investigation and Constitutive Modelling of High Strength 6xxx Series Aluminium Alloy: Precipitation Hardening Responses to FAST (Fast Light Alloys Stamping Technology) and Artificial Ageing