Abstract:So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoOx) to form a good contact. An a-Si:H(i)/MoOx stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al2O3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6" moly-poly cell, with an Al2O3/MoOx stack at the front side and n-type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al2O3 and MoOx layers, respectively. This resulted in an efficiency of 18.2% with a Voc of 651 mV, a FF of 75.6% and a Jsc of 36.9 mA/cm2. A post-deposition anneal (PDA) of the thin Al2O3 interlayer has significant effect on the Al2O3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher TPDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al2O3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.

Atomic Layer Deposition of Vanadium Oxide as Hole‐Selective Contact for Crystalline Silicon Solar Cells

Atomic-Layer-Deposited H:MoO x Function Layer as Efficient Hole Selective Passivating Contact in Silicon Solar Cells

Chromium Trioxide Hole-Selective Heterocontacts for Silicon Solar Cells

Improved V 2 O X Passivating Contact for p ‐Type Crystalline Silicon Solar Cells by Oxygen Vacancy Modulation with a SiO X Tunnel Layer

Atomic-layer-deposited Ultra-Thin VOx Film As a Hole Transport Layer for Perovskite Solar Cells

Solution-processed vanadium oxide by low-temperature annealing for silicon solar cells with hole selective contact

Interfacial Engineering of Cu 2 O Passivating Contact for Efficient Crystalline Silicon Solar Cells with an Al 2 O 3 Passivation Layer

Electron‐Selective Strontium Oxide Contact for Crystalline Silicon Solar Cells with High Fill Factor

Low-temperature Ta-doped TiO x electron-selective contacts for high-performance silicon solar cells

Effective Hydrogenation Strategies to Boost Efficiency over 20% for Crystalline Silicon Solar Cell with Al2O3/Cu2O Passivating Contact

Full-Area i-a-Si:H/ATO/Mg Electron-Selective Contacts for Silicon Solar Cells

Novel interlayer boosting the performance of evaporated Cu2O hole‐selective contacts in Si solar cells

Tuning oxygen vacancies in vanadium-doped molybdenum oxide for silicon solar cells with hole selective contact

A High-Quality Dopant-Free Electron-Selective Passivating Contact Made from Ultra-Low Concentration Water Solution

Investigation on the passivated Si/Al2O3 interface fabricated by non-vacuum spatial atomic layer deposition system

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Interface energy alignment of atomic-layer-deposited VOx on pentacene: An in situ photoelectron spectroscopy investigation

UV-Ozone Oxide layer for Junction Passivation and Passivating Contact Process of Silicon Solar Cells

21.16%-efficiency p-type TOPCon solar cell with ALD-Al2O3/MoOx/Ag as a hole-selective passivating contact

Constructing tin oxides Interfacial Layer with Gradient Compositions for Efficient Perovskite/Silicon Tandem Solar Cells with Efficiency Exceeding 28%

Spatial Atomic Layer Deposition of Molybdenum Oxide for Industrial Solar Cells