Abstract:The present work consisted in developing a computational routine for prediction and characterization ignition delay time, pressure, temperature generated and energy released in the combustion process in a shock tube. Mathematical modeling considered the high-pressure region of the shock tube known as the conducted section. The Lazarus code compiler was used to generate the unstructured triangular meshes and to implement the computational routines to simulate the propagation of shock waves inside the shock tube. The mathematical modeling used the geometric parameters of the shock tube of the combustion laboratory of the Federal University of Minas Gerais and was based only on the displacement of the shock wave after the diaphragm rupture. The main objective of the work was the development of computational routines to characterize the shock wave parameters of the ignition delay times of conventional diesel to validate the experimental tests carried out in the shock tube conducted by Santana et al. [3] and compare it with the experimental tests and numerical simulations carried out by other authors available in the literature. A linear regression of the experimental tests conducted by Santana et al. [3] with conventional diesel was performed to obtain the Arrhenius equation for numerical simulation of the ignition delay time of diesel under the following conditions: temperatures from 880 to 1300 K, pressures 24 bar and equivalence ratio 1. The results show good prediction between experimental tests and numerical simulations. Were found delay times ranging from 425 to 1890 μs. Considering all temperature range, the difference between the experimental and simulated test was approximately 15%, this difference also can be explained by the measurement in the shock tube, that the ignition delay time was calculated by the time difference between the passage of the shock wave by the pressure sensor and the start of the ignition detected by the luminosity detection sensor. This work is relevant because it was developed computational routine in open software and the results achieved in the simulation were considered satisfactory, since they are in the same order of magnitude as the results found in the experimental tests carried out by Santana et al. [3] and other works.

Evaluation of the corrections methodologies for improving the ignition delay time calculation in hydrogen/air mixtures using a design of experiments approach

Further study on the ignition delay times of propane-hydrogen-oxygen-argon mixtures: Effect of equivalence ratio

Shock Tube Study on Ignition Delay of Hydrogen and Evaluation of Various Kinetic Models

Experimental and Kinetic Study on Ignition Delay Times of Lean N -Butane/hydrogen/argon Mixtures at Elevated Pressures

Experimental and Kinetic Study on Ignition Delay Times of DME/H2/O2/Ar Mixtures

Experimental and modeling study on ignition delays of lean mixtures of methane, hydrogen, oxygen, and argon at elevated pressures

Correlations for the Ignition Delay Times of Hydrogen/air Mixtures

Measurements and kinetic study on ignition delay times of propane/hydrogen in argon diluted oxygen

Experimental analysis and numerical simulation of ignition delay time of diesel fuel using a shock tube

Experimental and Kinetic Study on Ignition Delay Times of Dimethyl Ether at High Temperatures

Experimental and modeling study on auto-ignition characteristics of methane/hydrogen blends under engine relevant pressure

Effect of Pressure and Equivalence Ratio on the Ignition Characteristics of Dimethyl Ether-Hydrogen Mixtures

Interpreting the Effect of Hydrogen Addition on the Auto-Ignition of Branched Alkane: A Case Study of Iso-Butane/hydrogen/o2/ar Mixtures

Experimental and Modeling Study on Ignition Delay Times of Dimethyl Ether/Propane/Oxygen/Argon Mixtures at 20 Bar

Minimum Ignition Energy of Methanol-Air Mixtures

Experimental and Modeling Study on Ignition Delay Times of Dimethoxy Methane/n-Heptane Blends

Ignition in Nonpremixed Counterflowing Hydrogen Versus Heated Air: Computational Study with Detailed Chemistry

Experimental and Kinetic Study on Ignition Delay Times of Methane/hydrogen/oxygen/nitrogen Mixtures by Shock Tube

Formulation reproducing the ignition delays simulated by a detailed mechanism: Application to n-heptane combustion

The Role of Third-Body Collision Efficiency in Autoignition of Hydrogen–Air Mixtures

Effects of Equivalence Ratio and Blending Ratio on the Ignition Delays of N-Pentane/hydrogen Mixtures under Engine Relevant Pressure