Abstract:Methods and results of the experimental and numerical investigation of the 1D heat transfer properties of a multifunctional syntactic foam. Top: experimental setup with schematic representation of the position of the thermocouples and boundary conditions; bottom left: microstructure of a representative sample of epoxy/hollow glass microspheres (HGM)/phase change material (PCM) syntactic foam; bottom right: temperature as a function of time in the heating experiment for the thermocouple located at 13 mm from the hot surface for different foam compositions. Data from the experiments (dotted line) and from the numerical modeling (solid line). Syntactic foams are lightweight porous composites obtained by the addition of hollow glass microspheres (HGMs) to a polymer matrix. This work experimentally and numerically investigates the thermal behavior of epoxy‐based syntactic foams with enhanced multifunctionality produced by incorporating microencapsulated phase change materials (PCMs) as functional fillers, providing thermal energy storage and temperature stabilization due to its large latent heat of melting. Foams are fabricated using varying ratios of HGMs (0–40 vol%) and PCM (0–40 vol%) to achieve tuned densities and thermal properties with a total filler content of up to 40 vol%. A one‐dimensional numerical heat transfer model based on the enthalpy method is presented to simulate the thermal behavior of these materials. The model accurately incorporates the specific heat and thermal conductivity of the foam components, as well as the latent heat absorption during PCM melting (up to 68 J/g). The model is experimentally validated by demonstrating good agreement with the measurements of transient temperature profiles during heating tests on the foam samples. The validated tool is then leveraged to model the thermal response of the foams under a sinusoidally varying heat source, similar to the possible real applicative scenarios. These results can help optimize foam compositions balancing energy storage density, heat transfer properties, and structural support for lightweight energy storage systems. Potential applications include high‐efficiency thermal management in battery packs, electronic cooling, solar energy storage, and sustainable temperature‐controlled buildings. Highlights Foams with 0–40 vol% PCM and 0–40 vol% HGM show up to 68 J/g latent heat. 1D numerical model accurately captures thermal conductivity and PCM phase change. Validated model simulates thermal response under sinusoidal heat, optimizing foam composition. Foams act as thermal reservoirs, maintaining up to 5°C lower surface temperatures than epoxy.

Supercritical fluid foaming of nanoscale phase patterned structures: An approach to lightweight hierarchical porous foams with superior thermal insulation

Using nanocapsules as building blocks to fabricate organic polymer nanofoam with ultra low thermal conductivity and high mechanical strength

Superlight, Mechanically Flexible, Thermally Superinsulating, and Antifrosting Anisotropic Nanocomposite Foam Based on Hierarchical Graphene Oxide Assembly.

Cyclic olefin copolymer foam: A promising thermal insulation material

Ultrasound and H2O assisted scCO2 foaming technology for preparation of PS/PMMA composite foams with ultra-lightweight and super thermal-insulation

A Hierarchical Mesoporous Insulation Ceramic.

Large-scale and facile fabrication of phenyl-containing silicone foam materials with lightweight, wide-temperature flexibility and tunable pore structure for exceptional thermal insulation

Light and strong nano-SiC foam with extremely low thermal conductivity

Advanced multifunctional Co/N co-doped carbon foam-based phase change materials for wearable thermal management

Strong silica-nanocellulose anisotropic composite foams combine low thermal conductivity and low moisture uptake

Lightweight Dual-Functional Segregated Nanocomposite Foams for Integrated Infrared Stealth and Absorption-Dominant Electromagnetic Interference Shielding

Modeling the thermal behavior of multifunctional syntactic foams containing phase change materials for heat management applications

Ultralight and Flexible Carbon Foam-Based Phase Change Composites with High Latent-Heat Capacity and Photothermal Conversion Capability

Facile Method for Preparing Hierarchical Al2O3-Glass Foam Ceramics with Superior Thermal Insulating Property.

Melt polymerization synthesis of a class of robust self-shaped olefin-linked COF foams as high-efficiency separators

Lightweight Porous Polystyrene with High Thermal Conductivity by Constructing 3D Interconnected Network of Boron Nitride Nanosheets

Design and electrospun closed cell structured SiO2 nanocomposite fiber by hollow SiO2/TiO2 spheres for thermal insulation

SiOC foam‐aerogel composites: Optimal balance of lightness and excellent thermal insulation

Ultralight Silica Foams with a Hierarchical Pore Structure Via a Surfactant-Free High Internal Phase Emulsion Process

Facile Method for Preparing Hierarchical Al 2 O 3 –Glass Foam Ceramics with Superior Thermal Insulating Property

Preparation of a High-Expansion-Ratio Blend Foam with Low Thermal Conductivity Using Poly(vinyl alcohol)-Polycaprolactone Mixture Solution via Supercritical Carbon Dioxide Foaming Technology