Abstract:Development of metallic glasses is hindered by the difficulties in manufacturing bulk parts large enough for practical applications. Spark plasma sintering (SPS) has emerged as an effective consolidation technique in the formation of bulk metallic glasses (BMGs) from melt-spun ribbons. In this study, Mg65Zn30Ca5 melt-spun ribbons were sintered at prolonged sintering times (15 min to 180 min) via SPS under a pressure of 90 MPa and at a temperature of 150 °C (which is below the crystallization temperature), to provide an insight into the influence of sintering time on the consolidation, structural, and biodegradation behavior of Mg-BMGs. Scanning Electron Microscopy was used to characterize the microstructure of the surface, while the presence of the amorphous phase was characterized using X-ray diffraction and Electron Backscatter Diffraction. Pellets 10 mm in diameter and height with near-net amorphous structure were synthesized at 150 °C with a sintering time of 90 min, resulting in densification as high as 98.2% with minimal crystallization. Sintering at extended durations above 90 min achieved higher densification and resulted in a significant amount of local and partial devitrification. Mechanical properties were characterized via compression and microhardness testing. Compression results show that increased sintering time led to better structural integrity and mechanical properties. Notably, SPS150_90 displayed ultimate compressive strength (220 MPa) that matches that of the cortical bone (205 MPa). Corrosion properties were characterized via potentiodynamic polarization with Phosphate Buffered Solution (PBS). The results suggest that the sintered samples have significantly better corrosion resistance compared to the crystalline form. Overall, SPS150_90 was observed to have a good balance between corrosion properties (10× better corrosion resistance to as-cast alloy) and mechanical properties.

Spark plasma sintering of sol–gel derived 45S5 Bioglass®-ceramics: Mechanical properties and biocompatibility evaluation

Effect of Borosilicate Glass on the Mechanical and Biodegradation Properties of 45S5-Derived Bioactive Glass-Ceramics

Preparation and Characterization of Low Temperature Heat-Treated 45S5 Bioactive Glass-Ceramic Analogues

Characterization of hydroxyapatite– and bioglass–316L fibre composites prepared by spark plasma sintering

Preparation and Characterization of Mechanical Properties of HAP/45S5 Bioglass Laminated Ceramic Composites via Spark Plasma Sintering

Sol-gel-synthesized bioglass-ceramics: physical, mechanical, and biological properties

Mechanical Properties and Biological Behavior of Gel-Derived Bioglass Ceramic

Low-temperature Sintering of 45S5 Bioglass®-based Glass Ceramics: Effect of Biphasic Mixing Approach on the Mechanical and Biological Properties

Microstructures and properties of 45S5 bioglass® & BCP bioceramic scaffolds fabricated by digital light processing

Fabrication And Characterization Of Tricalcium Silicate Bioceramics With High Mechanical Properties By Spark Plasma Sintering

Effect of sintering temperature on bioactivity and degradability of the sol-gel derived glass in the system CaO-P2O5-SiO 2

Phase transformation and mechanical properties of new bioactive glass-ceramics derived from CaO-P2O5-Na2O-B2O3-SiO2 glass system

Investigation of Spark Plasma Sintering on Microstructure-Properties of Zirconia Reinforced Fluormica Glass for Dental Restorations

Enhancing Mechanical and Biocorrosion Response of a MgZnCa Bulk Metallic Glass through Variation in Spark Plasma Sintering Time

Synthesis of 30wt%bas/si3n4 Composite by Spark Plasma Sintering

Investigation of citric acid-assisted sol-gel synthesis coupled to the self-propagating combustion method for preparing bioactive glass with high structural homogeneity

Liquid Phase Sintered Ceramic Bone Scaffolds by Combined Laser and Furnace

Fabrication and Characterization of 45S5 Bioglass Reinforced Macroporous Calcium Silicate Bioceramics

Improved Mechanical Properties of Dense Β-Si3n4 Ceramics Fabricated by Spark Plasma Sintering with Al2O3-YSZ Additives

Biological Properties of Gel-derived Bioglass Ceramics in Vitro and in Vivo

Identification of the wollastonite phase in sintered 45S5 bioglass and its effect on in vitro bioactivity