Abstract:Cu has been adopted to replace Al for conduction lines and contact structures in very large-scale integrated circuits due to its low resistivity. However, Cu could rapidly react with the SiO2-based dielectric under 300 degrees C and form deep level impurities which are strong sink for carriers, leading to the dielectric degradation of the devices. Therefore, it is important to insert a stable barrier between the Cu wiring and SiO2-based dielectric for suppressing Cu diffusion and improving the adhesive strength. The prediction of international technology roadmap for semiconductors that the thickness of diffusion barrier would be further reduced to 3 nm for 22 nm technology node indicates the widely being used Ta/TaN barrier would be incompetent in the future, since Ta/TaN barrier at the limited thickness exhibits a high resistivity and a columnar grain structure which provides lots of vertical grain boundaries for Cu diffusion. Therefore a directly platable amorphous single barrier with low resistivity is highly desired. In this work, MoC are chosen as impurity to expect for amorphous Ru-based films. The RuMoC films with different components were deposited by RE magnetron co-sputtering with different deposition power ratios of MoC versus Ru targets. The sheet resistances, microstructures and components of the RuMoC films in Ru-MoC/Si and Cu/RuMoC/p-SiOC: H/Si structures were studied. The sheet resistances, residual oxygen contents and microstructures of the RuMoC films have close correlation with the doping contents of Mo and C elements which can be easily controlled by tuning the deposition power on MoC target. When the deposition power ratio of MoC versus Ru targets was 0.5, amorphous RuMoC II film with low sheet resistance and residual oxygen content was obtained. After annealing at 500 degrees C the Mo-C and Ru-C bonds were well-preserved and co-suppressed the recrystallization of the film and the increasing of the oxygen content, contributing to excellent thermal stability and electrical properties of Cu/RuMoC II/p-SiOC: H/Si film.

RuAl thin film deposition by DC magnetron sputtering

RuAl intermetallic compound of low resistivity scaling and high thermal stability as potential interconnect metallization

Growth Characteristics and Properties of RuAlO Hybrid Films Fabricated by Atomic Layer Deposition

Ru Thin Film Formation Using Oxygen Plasma Enhanced ALD and Rapid Thermal Processing

Fabrication of Cr2AlB2 and Cr4AlB4 MAB Phase Coatings by Magnetron Sputtering and Post-Annealing

Microstructure, infrared optical properties and thermal stability of ZrB2 and double-layer-structure Al2O3/ZrB2 thin films by magnetron sputtering technique

Influence of co-sputtering AlB2 to TaB2 on stoichiometry of non-reactively sputtered boride thin films

Ru$_{2-x}$Mn$_{1+x}$Al thin films

Synthesis and Elastic Properties of V2alc Thin Films by Magnetron Sputtering from Elemental Targets

Phase transformation and water adsorption behavior of ALD deposited and annealed Ru and RuO2 films

Cohesive properties, electronic structure, and bonding characteristics of RuAl—A comparison to NiAl

Microstructure and Thermal Stability of Moc Doped Ru-Based Alloy Films As Seedless Diffusion Barrier

Phase composition and transformations in magnetron-sputtered (Al,V)2O3 coatings

Synthesis, microstructure and properties of MoAlB MAB phase films

RBS/Channeling characterization of Ru(0001) and thin epitaxial Ru/Al$_2$O$_3$(0001) films

Deposition and Characterization of Ti2AlC MAX Phase and Ti3AlC Thin Films by Magnetron Sputtering

Comparison of the Ru thin films grown on Si, TiN/Si and TaN/Si substrates by plasma enhanced atomic layer deposition

Low-temperature Deposition of Α-Al2o3 Films by Reactive Sputtering Al+α-Al2O3 Target

Synthesis of Cr2AlC Thin Films by Reactive Magnetron Sputtering

The Influence of Cr Content on the Phase Structure of the Al-rich Al-Cr-O Films Deposited by Magnetron Sputtering at Low Temperature

Ultrathin, sputter-deposited, amorphous alloy films of ruthenium and molybdenum