Abstract:Abstract In the pursuit of increasing their profitability, the design and operation of combined cycle power plants needs to be optimized for new liberalized markets with large penetration of renewables. A clear consequence of such renewable integration is the need for these plants for being more flexible in terms of ramping-up periods and higher part-load efficiencies. Flexibility becomes an even clearer need for combined heat and power plants to be more competitive, particularly when simultaneously following the market hourly price dynamics and varying demands for both the heat and the electricity markets. In this paper, three new plant layouts have been investigated by integrating different storage concepts and heat-pump units in key sections of a traditional plant layout. The study analyses the influence that market has on determining the optimum layouts for maximizing profits in energy-only markets (in terms of plant configuration, sizing and operation strategies). The study is performed for a given location nearby Turin, Italy, for which hourly electricity and heat prices, as well as meteorological data, have been gathered. A multi-parameter modeling approach was followed using KTH’s in house techno-economic modeling tool, which uses time-dependent market data, e.g. price and weather, to determine the trade-off curves between minimizing investment and maximizing profits when varying critical size-related power plant parameters e.g. installed power capacities and storage size, for pre-defined layouts and operating strategies. A comparative analysis between the best configurations found for each of the proposed layouts and the reference plant is presented in the discussion section of the results. For the specific case study set in northern Italy, it is shown that the integration of a pre-cooling loop into baseload-like power-oriented combined cycle plants is not justified, calling for investigating new markets and different operating strategies. Only the integration of a heat pump alone was shown to improve the profitability, but within the margin of error of the study. Alternatively, a layout where district heating supply water is preheated with a combination of a heat pump with hot thermal tank was able to increase the internal rate of return of the plant by up to 0.5%, absolute, yet within the error margin and thus not justifying the added complexity in operation and in investment costs. All in all, the analysis shows that even when considering energy-only market revenue streams (i.e. heat and electricity sells) the integration of heat pump and storage units could increase the profitability of plants by making them more flexible in terms of power output levels and load variations. The latter is shown true even when excluding other flexibility-related revenue streams. It is therefore conclusively suggested to further investigate the proposed layouts in markets with larger heat and power price variations, as well as to investigate the impact of additional control logics and dispatch strategies.

Flexible operation and integration of high-temperature heat pumps using large temperature glides

Large-scale heat pumps: Applications, performance, economic feasibility and industrial integration

Heat pumps optimal sizing and operation accounting for techno-economic and environmental aspects

Optimal Installation of Heat Pumps in Large District Heating Networks

Assessing the Flexibility Potential of Industrial Heat–Electricity Sector Coupling through High-Temperature Heat Pumps: The Case Study of Belgium

Improving the Economic Efficiency of Heat Pump Integration into Distillation Columns of Process Plants Applying Different Pressures of Evaporators and Condensers

Heat pumps as a sustainable bridge for global heating and cooling at multi-scale

Combined Cycle, Heat Pump, and Thermal Storage Integration: Techno-Economic Sensitivity to Market and Climatic Conditions Based on a European and United States Assessment

Modeling the Value of Flexible Heat Pumps

The potential of decentral heat pumps as flexibility option for decarbonised energy systems

Techno-Economic Comparative Analysis of Innovative Combined Cycle Power Plant Layouts Integrated With Heat Pumps and Thermal Energy Storage

High‐Temperature Heat Pumps for Industrial Use

Application of customized absorption heat pumps for utilization of low-grade heat sources

Potential evaluation of integrated high temperature heat pumps: A review of recent advances

Exploiting Flexibility of District Heating Networks in Combined Heat and Power Dispatch

A multiperiod approach for waste heat and renewable energy integration of industrial sites

Nonlinear operational optimization of an industrial power-to-heat system with a high temperature heat pump, a thermal energy storage and wind energy

Model Predictive Control of Heat Pumps with Thermal Energy Storages in Industrial Processes

Thermodynamic analysis and heat exchanger calculations of transcritical high-temperature heat pumps

Break-even of high-temperature heat pump integration for milk spray drying

Evaluation of the Optimum Hybrid Power to Heat Configuration for a Gas Turbine Based Industrial Combined Heat and Power Plant