Abstract:In extruded HVDC cable systems a variety of interface types can be found, and the interfacial properties depend on the application within the system. Such applications can be joints, terminations or the cable itself and they will all have different material combinations and manufacturing methods. To ensure at least 40 years of faultless operation of the cable system and its interfaces, proper design and quality control is essential. This requires detailed knowledge on how physical, measurable quantities of polymer surfaces relate to electrical characteristics such as electric field and space charge accumulation. This work aims to expand our understanding by assessing polymer surfaces created with different, industrializable preparation methods resulting in varying degree of surface roughness. Breakdown tests, charge decay measurements, optical profilometry and other characterization methods have been performed on cable peelings created from full-sized HVDC cables. It was found that, depending on preparation method, very different roughness levels and textures are created on the polymer surfaces. There were also other impacts of the preparation method found, such as altered surface morphology or the introduction of surface states. A clear relation between surface roughness and the localized field distribution was found, which mainly depended on the arithmetical surface height parameter Sa, but also to a minor degree on the shape of the surface texture. Field dependent bulk conductivity was found to reduce the tail in the surface field distribution histogram, but was not able to fully remove the distribution itself. The surface field distribution showed to have a clear impact on space charge injection, and was capable of creating a field threshold effect. This effect could not be accounted for by a fixed field parameter in the Schottky equation. In this work, charge injection was assumed to be the sum of Schottky and Fowler-Nordheim injection, which resulted in a very significant increase in charge injection above the threshold field. This led to bulk-limited charge injection above the threshold field, along with significant homocharge accumulation. Increased roughness was observed to reduce the breakdown field in the tested samples, which for the larger test objects scaled well with the calculated threshold fields. For the cable peelings, an impact of surface roughness was found as well, but at significantly higher field levels. The origin of this scaling effect is further discussed in this thesis. The threshold fields were also found for rough surfaces in the charge decay measurement. By utilizing rough ground electrodes, significantly higher decay currents were measured above the field thresholds. The increase in decay speed is related to opposite charge injection during the poling phase before the measurement. The findings of this work are believed to be applicable to many high voltage applications, especially in cases where solid insulation with low conductivity is used at high electric fields.

A Study on the Behavior of Interfacial Space Charge at Polymer Dielectric Double-Layer Simulating the HVDC Cable Joints

Space Charge Accumulation at Material Interfaces in HVDC Cable Insulation Part I—Experimental Study and Charge Injection Hypothesis

Automated Space Charge Classification Inside ±500-Kv HVDC Cable Insulation Using Fusion of Superpixel and Deep Features for Remote Condition Assessment.

Study on space charge accumulation characteristics of 320 kV cross-linked polyethylene cable joints

Electrical Insulation Properties of Material Interfaces in HVDC Cable Factory Joint

Space Charge Accumulation at Material Interfaces in HVDC Cable Insulation Part II—Simulations of Charge Transport

Insulation Properties and Interfacial Quantum Chemical Analysis of Cross-Linked Polyethylene under Different Degassing Time for HVDC Cable Factory Joint Applications

Interfacial Microstructure and Insulation Properties of 500 Kv EHVDC XLPE Cable Factory Joint under Different Roughness and Degassing Durations

Space Charge Accumulation between Different Insulating Materials Simulated Cable Joint for HVDC

Charge Transport in Full-Size HVDC Cable Joint with Modeling of XLPE/EPDM Interface

Effect of Space Charge on Interface Discharge Characteristics in Multilayer Dielectric

Space Charge and Electric Field Characteristics in XLPE-Insulated Extrusion Molded Joint for HVDC Submarine Cables: Experiment and Simulation

Two-dimensional Space Charge Measurement in Cable Joint Model Using the Pulsed Electroacoustic Method

Surface Layer Fluorination-Modulated Space Charge Behaviors in HVDC Cable Accessory

Characterization of Different Interface Types for HVDC Extruded Cable Applications

An Improved Space Charge Measurement Approach for Power Cables

Interface charge accumulation in Bi-layer dielectrics between cable and accessory insulation under temperature gradient

Space Charge Behavior in LDPE/EBA Insulation Materials for HVDC Cables

Polarity Effect on Space Charge Distributions in Polymer Under DC Electric Field

Space charge behaviors in cable insulation under a direct current‐superimposed pulsed electric field

Space Charge Suppression of Polyethylene Induced by Blending with Ethylene-Butyl Acrylate Copolymer