Abstract:Abstract The demand for gas-turbine (GT) based flexible power generation and mechanical drive is increasing due to the growing penetration of renewables and due to the need to quickly adjust production and operate at part load respectively. As efficiency operability low emissions, small footprint, availability and maintainability are of paramount importance, engine designers are leaning towards aircraft engine architectures that, with appropriate modifications mostly to the combustion system and turbine, can meet market needs. To leverage the large experience from aircraft propulsion, aero-derivative engines maintain the same architecture, with a high-speed shaft core, and a low-speed shaft driven by a multi-stage low-pressure turbine. While in aircraft engines power is adjusted by changing fuel rate and shaft speed, that go hand in hand, mechanical drive engines have more stringent needs that require changing the delivered power by keeping the shaft speed under control to guarantee the operation of the driven equipment (an LNG compressor or an electric generator). Therefore, the power turbine may deliver exit flow profiles and angles that put the turbine exhaust diffuser under severe off-design conditions, with the onset of large scale separations, large kinetic losses, and ultimately a significant drop on cycle performance. This paper describes Baker Hughes, a GE company experience in the CFD assisted design and scale-down testing of aero-derivative exhaust diffusers. The design incorporates the requirements of hot-end mechanical drive in multiple the power turbine operating conditions to determine the best compromise between peak design performance and off-design operability. The test in similitude conditions considered four relevant operating points. The inlet conditions matched with the power turbine exit profiles by the concerted action of swirl vanes and perforated plates, the design of which was heavily CFD assisted. Predictions matched measurements in terms of pressure recovery, kinetic losses, and exhaust velocity profiles. Different data post-processing and averaging were considered to properly factor in the diffuser losses into the overall turbine performance.

Experimental analysis and design optimization of an empty diffuser for performance Enhancement in DAWT

Optimization Based on Computational Fluid Dynamics and Machine Learning for the Performance of Diffuser-Augmented Wind Turbines with Inlet Shrouds

Building integrated diffusers' area ratio optimization

Sensitivity study of diffuser angle and brim height parameters for the design of 3 kW Diffuser Augmented Wind Turbine

Performance evaluation of a downwind diffuser on vertical axis wind turbine

Velocity Augmentation Model for an Empty Concentrator-Diffuser-Augmented Wind Turbine and Optimisation of Geometrical Parameters Using Surface Response Methodology

Aerodynamic Design and Performance Evaluation of Pipe Diffuser for Centrifugal Compressor of Micro Gas Turbine

Performance and flow characteristics of a novel air bleeding aerodynamic combustor diffuser

INVESTIGATION OF THE MAP WIDTH IMPROVEMENT IN A RADIALLY REDUCED DIFFUSER DESIGN CONCEPT FOR A CENTRIFUGAL COMPRESSOR

Automated shape optimisation of a plane asymmetric diffuser using combined Computational Fluid Dynamic simulations and multi-objective Bayesian methodology

Performance Analysis of Two-Dimensional Plane Diffusers at a Moderate Reynolds Number by Means of Unsteady RANS

A Numerical Study On The Flow Mechanism Of Performance Improvement Of A Wide-Angle Diffuser By Inserting A Short Splitter Vane

An Experimental Investigation of the Performance Impact of Swirl on a Turbine Exhaust Diffuser/Collector for a Series of Diffuser Strut Geometries

Numerical Study And Optimization Of Corrugation Height And Angle Of Attack Of Vortex Generator In The Wavy Fin-And-Tube Heat Exchanger

Numerical Study of the Improvement in Stability and Performance by Use of a Partial Vaned Diffuser for a Centrifugal Compressor Stage

Experimental and large-eddy simulation study of swirling air jet: Application for the improvement of the spatial temperature homogeneity

Detached Eddy Simulation and PIV Validation of the Flow in a Compact Return Diffuser

Design, Testing, and Performance Impact of Exhaust Diffusers in Aero-Derivative Gas Turbines for Mechanical Drive Applications

CFD studies of the effect of holes and angles of upstream duct of horizontal axis wind turbines

Design and flow analysis of variable geometry wedge diffuser

Performance Improvement of a High Loading Centrifugal Compressor with Vaned Diffuser by Hub Contour Optimization