Abstract:To alleviate the shortage of river sand (RS) and recycle abandoned resources, two recycled manufactured sands (RMSs) produced from tunnel excavation rock (tuff manufactured sand, TS) and granite cutting waste (granite manufactured sand, GS) are studied and compared with standard sand (SS) and RS. The aim is to identify the application potential of the two RMSs in cement-based materials. This is done by analyzing their influences on the mortar properties based on their surface characteristics and establishing a correlation between the surface characteristics of RMS and mortar properties. For the parent rock, petrographic analysis is performed and the uniaxial compressive strength is measured. For sand, the physical properties are evaluated and X-ray diffraction is used for analyzing the chemical composition. Digital image processing, nitrogen adsorption, and X-ray computed tomography are employed to determine the surface characteristics of sand particles. For the mortar, the fluidity, mechanical strength, water absorption, early total shrinkage, and accelerated expansion ratio are measured. The microstructure of the mortar interface transition zone is examined. Mercury intrusion porosimetry and thermogravimetric analysis are conducted to study the internal mechanism. The results indicate that compared with SS, the two RMSs reduce the fluidity of fresh mortar. In addition, TS is beneficial for the flexural, compressive, and tensile strengths of hardened mortar because of its denser internal pore structure and high degree of hydration caused by the properties of sand. The mechanical strength of the GS mortar can reach a similar or slightly higher level than that of the SS mortar. Furthermore, the fluidity and mechanical strength are well correlated with two parameters of sand, namely, roundness and specific surface area. The tensile strain capacity of the RMS-based mortar is superior to those of the SS and RS mortars. However, RMS increases the early total shrinkage. Although the TS mortar has the highest tensile strain capacity, it also has the largest early total shrinkage among the four mortar mixtures. Comparing the escalations in tensile strain capacity and early total shrinkage, the TS increases the risk of shrinkage cracking in the early stages. The effect of GS on the mortar tensile strain capacity is slightly greater than that on the early total shrinkage; thus, there is no significant influence on the risk of early shrinkage cracking in the GS mortar. In the accelerated expansion test, the TS shows potential alkali-silica reaction (ASR) risk in accordance with ASTM C1260, however, the GS indicates no potential for expansion damage. Based on the performance of various sands and mortars, GS has a better application value than TS. As for the TS mortar, it is necessary to consider the shrinkage cracking risk and ASR hazard in practical applications.

Stress-strain behaviour of cement mortars containing recycled glass during and after exposure to elevated temperatures

Application Potential of Granite Cutting Waste and Tunnel Excavation Rock As Fine Aggregates in Cement-Based Materials Based on Surface Characteristics

Experimental Study of Micro/macro Crack Development and Stress–strain Relations of Cement-Based Composite Materials at Elevated Temperatures

Mechanical properties and durability evaluation of self-compacting mortars containing glass and brick powders

Influence of waste glass powder as a supplementary cementitious material (SCM) on physical and mechanical properties of cement paste under high temperatures

The effect of extensive heat exposure on the mechanical properties of polymer-modified sulfoaluminate cement repair mortar

Correlation Between Macroscopic Properties and Microscopic Pore Structure in Steel-Basalt Hybrid Fibers Reinforced Cementitious Composites Subjected to Elevated Temperatures

Dynamic Mechanical Properties of Slag Mortar with Alkali-Resistant Glass Fiber

Influence of elevated temperature on the microstructures and mechanical properties of cement-based mortar with sands and refractory materials

Experimental and numerical study of long-term alkali-silica reaction (ASR) expansion in mortar with recycled glass

Change of the Coefficient of Thermal Expansion of Mortar Due to Damage by Freeze Thaw Cycles

An innovative way to enhance the high temperature properties of alkali activated cement mortars prepared by using glass powder as precursor

Effect on Compression Strength of Masonary Mortar by Replacing Fine Aggregates with Waste Glass

Studying the Effects of Varied Dosages and Grinding Times on the Mechanical Properties of Mortar

High temperature resistance of fly ash/GGBFS-based geopolymer mortar with load-induced damage

Mechanical and Material Properties of Mortar Reinforced with Glass Fiber: An Experimental Study

A ternary optimization of alkali-activated cement mortars incorporating glass powder, slag and calcium aluminate cement

Bond behaviour between steel fibre and cement mortar exposed to elevated temperature

Recycling of Glass Cullet and Glass Powder in Alkali-Activated Cement: Mechanical Properties and Alkali–Silica Reaction

Study on the Strength and Hydration Behavior of Sulfate-Resistant Cement in High Geothermal Environment

Effect of Elevated Temperature on Mechanical Properties of High-Volume Fly Ash-Based Geopolymer Concrete, Mortar and Paste Cured at Room Temperature