Abstract:Porous NiTi lattice structures are widely used in the manufacture of crucial components owing to their excellent shape memory effect, superelasticity, and high damping capacities. However, the specific strength and lightweight characteristics of porous NiTi lattice structures fabricated by conventional technologies are limited by unpredictability. In this work, three types of porous NiTi structures based on triply periodic minimal surface (TPMS) – Diamond, Gyroid, and Primitive – were designed and manufactured by the laser powder bed fusion (LPBF) additive manufacturing process . This work demonstrates LPBF is a feasible and efficient approach to fabricate highly accurate porous NiTi TPMS structures. Moreover, the influence of each of these structures on the mechanical and shape memory properties was investigated. Among the three structures, Gyroid had the smallest volume fraction deviation. Furthermore, the Diamond structure had the largest compressive modulus (782.82 MPa) and ultimate yield strength (163.14 MPa). The Gyroid and Primitive structures exhibit excellent elastic recovery deriving from high values of compressive modulus (662.44 MPa, and 703.29 MPa), and can maintain reliable structural robustness. The Primitive structure exhibited the lowest mechanical properties (37.80 MPa). During the cyclic compression test, Gyroid and Primitive show a smaller unrecovered strain than Diamond. Primitive shows the largest recovered strain during the heating process (6.98%). The higher mechanical flexibility of Primitive structure endows this structure with higher recovery ratio. During the direct compression test, the residual strain exhibits a positive correlation with the loading strain. All three structures exhibit good deformation recovery capability with a strain of 4%. At a strain of 12%, recovered strain during heating became the dominant factor in the recovery of the TPMS structure. Overall, porous NiTi TPMS structures are capable of reversible compressibility composed of rapid elastic recovery and controllable shape memory recovery. The unique performance of porous NiTi TPMS structure fabricated by LPBF renders it a highly efficiency energy-absorbing structure.

Nitrogen-assisted laser-based powder bed fusion fabricated NiTi with high hardness and low modulus

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

Laser powder bed fusion of nitinol shape memory alloy with superelastic characteristics on Ti substrate

Laser powder bed fusion additive manufacturing of NiTi shape memory alloys: A review

Fabrication of multi-functional Ni–Ti alloys by laser powder bed fusion

Micro laser powder bed fusion of NiTi alloys with superior mechanical property and shape recovery function

Effect of microstructure on the superelasticity of high-relative-density Ni-rich NiTi alloys fabricated by laser powder bed fusion

Fabrication of Integrated Ni-Ti Alloys Possessing Both Super-elastic and Shape Memory Properties by Laser Powder Bed Fusion

Volume Fraction Effect on the Mechanical and Shape Memory Properties of NiTi Gyroid Lattice Structure Fabricated by Laser Powder Bed Fusion

Porous NiTiNb alloys with superior strength and ductility induced by modulating eutectic microregion

Superelastic NiTi Functional Components by High-Precision Laser Powder Bed Fusion Process: The Critical Roles of Energy Density and Minimal Feature Size

Additively manufacturing-enabled hierarchical NiTi-based shape memory alloys with high strength and toughness

Ni-Ti-Zr ternary alloy with high transition temperature fabricated by laser powder bed fusion

Enhancing the surface finish and corrosion resistance of laser powder bed fusion NiTi surfaces through chemical polishing

Laser Polishing of Nickel-Titanium Shape Memory Alloy Produced via Laser Powder Bed Fusion

Effect of a constant laser energy density on the evolution of microstructure and mechanical properties of NiTi shape memory alloy fabricated by laser powder bed fusion

In-situ synthesis of high strength and toughness TiN/Ti6Al4V sandwich composites by laser powder bed fusion under a nitrogen-containing atmosphere

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Microstructure and Mechanical Properties of NiTi Shape Memory Alloys by Laser Engineered Net Shaping

Mechanical and shape memory properties of NiTi triply periodic minimal surface structures fabricated by laser powder bed fusion

Effect of laser printing mode on surface topography, microstructure and corrosion property of additive manufactured NiTi alloy