Abstract:Heavy metal-based vehicle caused increase in fuel consumption, which creates pollution in the environment; thus, scientists across the nation researched to produce light weight, cost-effective, easy degradable, corrosive resistant composite material. Due to such features present in the composite material, the present research aims to examine the impact of alkali-silane treatment on the time-dependent and machining behavior of composites. Further, the alkali treatment and silane treatment on fiber and filler particle are carried out to provide even dispersion of filler particle and better reinforcement and interfacial bonding adhesion to the composite material, which makes a novelty to this study. The obtained fiber and filler particle were reinforced to matrix by using hand layup method and subsequently cured. This prepared composite material's strength is analyzed as per the ASTM standards. The results indicate that the inclusion of surface modified corn-fiber reinforced EF composite shows stronger interfacial adhesion, which implies loss factor of 42.8% lower than neat epoxy. Similarly, reinforcing corn husk fiber increases the energy release rate by 2500% and the fracture toughness by 156.47% when compared to pure epoxy composite. Further, the inclusion of biosilica particle of 2.0 vol.% exhibited the highest storage modulus of 5.69 GPa and the lowest loss factor of 0.32. This demonstrates the beneficial effect of combining alkali and silane treatment on corn fiber and filler particle. The epoxy composite (EFP3) of chemically treated fiber 30 vol.% and 2 vol.% of biosilica reinforcement exhibits a higher fatigue life cycle, fracture toughness, and energy release rate of 30,546, 26.5 MPa√m, and 0.86 MJ/m 2 , respectively. Similarly, the composite designation EFP3 has the lowest contact angle of 78°, indicating the preserved hydrophobicity. A drilling study has shown that using a 4-mm drill bit and 8-mm drill bit. The resultant of the drilling studies concludes that the use of 2.0 vol.% biosilica reduced the occurrence of fiber pull-out while drilling. Owing to such improved strength properties, light weight, corrosive resistant features in the biocomposite are applied in industries such as automotive, sporting goods, food and drug packaging, aerospace, and other technical applications that require strong load-bearing capacity, etc.

Effects of chemical treatment on natural (rice straw/neem saw dust) fiber morphology and mechanical properties of its composite material

Effect of Chemical Treatment on Rice Straw Fiber Surface and Properties of Straw/Polylactic Acid Composites

Effect of cashew nut shell liquid on mechanical, thermal and morphological properties of paddy straw filled phenolic composites

Effect of alkali treatment on mechanical and water absorption properties of biodegradable wheat-straw/glass fiber reinforced epoxy hybrid composites: A sustainable alternative for conventional materials

Study of Sound Absorption Coefficients and Characterization of Rice Straw Stem Fibers Reinforced Polypropylene Composites

Effect of silane treatment on corn husk and tamarind fiber and betel nut filler on fatigue, thermal conductivity, and machining behavior of epoxy biocomposites

Enhancing mechanical properties of natural waste‐based composites for automobile and plastic industry

Effects of water absorption on the mechanical properties of hybrid natural fibre/phenol formaldehyde composites

Study on Epoxy Resin Composite Reinforced with Rice Straw Fiber

Valorisation of corn waste as fiber, biosilica, and their epoxy composites: fatigue, fracture toughness, water absorption, and drilling properties

Mechanical, morphological and wear resistance of natural fiber / glass fiber-based polymer composites

Mechanical characterization and machining performance evaluation of rice husk/epoxy an agricultural waste based composite material

Characterization of heat-treated rice husk Si3N4 bioceramic on cellulosic corn husk fiber-polyester composite

Study on the modification of polyester resin bamboo fiber-based composite with euphorbia coagulum and their effect on mechanical and thermal properties

Development and characterization of polymer composites with cotton straw fiber derived from agricultural wastes

Experimental investigation on mechanical and tribological analysis of pineapple leaf ( Ananas comosus ) and sisal ( Agave sisalana ) fibers reinforced hybrid epoxy composites

Development of silane-treated corn husk fiber and agro-waste biofiller-reinforced epoxy composite: effects on wear, mechanical, thermal, and water absorption properties

Mechanical and flammability properties of ultrasonically processed silane-treated areca-banana fiber-reinforced epoxy composites for lightweight applications

Influence of rice husk ash Si3N4 ceramic on mechanical, wear and low cycle fatigue behavior of hybrid pineapple/basalt fiber reinforced polyester composite

The Influence of Chemically Treated Hemp Fibre on the Mechanical Behavior and Thermal Properties of Polylactic Acid Made with FDM

Experimental Investigation on Thermal Behaviors of Benzoyl Treated Neem / Pineapple Fiber Reinforced Saw Dust Filled Epoxy Hybrid Green Composites