Abstract:Cold spray additive manufacturing (CSAM) is relatively a new additive manufacturing technology that does not employ heat to achieve bonding between metal particles and the substrate. The CSAM process operates at a temperature lower than the melting temperature of the metal particle and the substrate. Hence, the constraints associated with high-temperature processing such as oxidation and phase change can be minimised, as well as the requirement of energy can be significantly reduced. This technology offers promising solutions for a wide range of applications in industries such as automotive, aerospace, and nuclear power generation. In this study, the effects of build orientation and post-build heat treatment on additively manufactured (AM) copper were investigated. Copper deposits were fabricated using a novel spraying system where stationary nozzle propels metal particles by compressed air onto a substrate clamped on a moving robot arm. The deposits were built in two different orientations (XY—0° and Z—90° to the build platform, respectively) and then mechanically tested in the as-deposited (AD), annealed at 400 °C (400 M), and sintered at 1000 °C (1000 M) conditions. The results strongly suggested that Z-build orientation samples had substantially lower inter-particle bonding strength compared with the XY-build direction samples due to the presence of porosity network. This pore network was created when the spray angle was abruptly changed from 90 to 45° orientation. The metallurgical bonding between particles improved with subsequent heat treatment. The 400 M samples consisted of recrystallised microstructure leading to an increase in tensile strength and ductility. Although the metallurgical bonding in the 1000 M samples was comparably better than the as-desposited samples, the formation of grossly large pores along grain boundaries acted as crack initiation sites, thereby resulting in very poor mechanical properties. This study has provided insights into the CSAM processing parameter selection and potential post-processing route to improve the mechanical properties of cold-sprayed copper parts.

Cold Spray Additive Manufacturing of Ti6Al4V: Deposition Optimization

Advancements in Cold Spray Additive Manufacturing: Process, Materials, Optimization, Applications, and Challenges

Experimental and Numerical Study of Al2219 Powders Deposition on Al2219-T6 Substrate by Cold Spray: Effects of Spray Angle, Traverse Speed, and Standoff Distance

Influence of spray angle in cold spray deposition of Ti-6Al-4V coatings on Al6061-T6 substrates

Microstructural evolution and mechanical property of Ti-6Al-4V wall deposited by continuous plasma arc additive manufacturing without post heat treatment

Optimizing the Corrosion Resistance of Cold Spraying Additive Manufactured FeCoNiCrMn High Entropy Alloy: Improving Particle Bonding Quality Through Heat Treatment

Cold Sprayed Additive Manufacturing of SiC/Al Metal Matrix Composite: Synthesis, Microstructure, Heat Treatment and Tensile Properties

Effects of different heat treatments on anisotropy of cold sprayed 7075 Al deposits

Tuning the microstructure and mechanical properties of additive manufactured aluminum matrix composites by cold spray

Achieving ultrafine grain strengthening C f /SiC-GH3536 joints brazed with Cu-Ti-WC composite interlayer via cold spray additive manufacturing

Forming Behavior of Additively Manufactured Al/Ti Material Compounds Produced by Cold Spraying

Microstructure and mechanical properties of as-built and heat-treated Ti-6Al-4V alloy prepared by cold metal transfer additive manufacturing

Solid-State Cold Spray Additive Manufacturing of Ni-Based Superalloys: Processing–Microstructure–Property Relationships

Numerical Study on Particle Behavior and Deposition Accuracy in Cold Spray Additive Manufacturing

Study of microstructural and mechanical anisotropy of 7075 Al deposits fabricated by cold spray additive manufacturing

Effect of build orientation and post-build heat treatment on the mechanical properties of cold spray additively manufactured copper parts

The effect of the deposition strategy and heat treatment on cold spray additive manufactured 316L stainless steel

Cost-affordable Ti-6Al-4V for Additive Manufacturing: Powder Modification, Compositional Modulation and Laser In-Situ Alloying

A Review of Additive Manufacturing Techniques and Post-Processing for High-Temperature Titanium Alloys

Numerical Simulation, Microstructure, and Properties of TC4 Plasma Arc Additive Manufactured Thin Wall

Additive manufacturing of Ti-6Al-4V alloy- A review