Abstract:Temporary plugging technology is an important drilling technique for maintaining wellbore stability and resolving lost circulation problems. The key to its success lies in the use of materials that can form a tight and stable "temporary plugging layer" with certain pressure bearing capacity and a permeability close to zero in the loss channel near the wellbore. Experimental studies have been conducted to develop adhesion formulations for optimal temporary plugging materials, as the matching relationship between particle size and fracture width is critical [(0.5−1)/1]. By measuring the permeability of the temporary plugging layer under varying confining pressure with a soap foam flowmeter, researchers have been able to evaluate the effectiveness, degradation, and dosages of temporary plugging agents. It has been shown that a single-particle material, such as a walnut shell, has a smaller permeability than a hyperfine CaCO 3 coated temporary plug layer. The latter, however, is less capable of bearing pressure. By combining different materials, such as walnut shells and hyperfine CaCO 3 particles, the researchers were able to create a temporary plug layer that had the lowest permeability and did not change much at variable confining pressures. Its pressure-bearing capacity is strong and the temporary plug works well. Experiments have shown that a ratio of 2:1–3:1 of hyperfine CaCO 3 and walnut shell particles work well for plugging a fracture system with particles of size 2–3 times the fracture width. It developed an evaluation method for temporary plugging agents, studied their plugging capability and degradation performance for reservoir conversion, and evaluated degradation performance after successful temporary plugging. The temporary plugging rate of the temporary plugging agent increased from 98.10% to 99.81%, and the maximum temporary plugging pressure is 50.39 MPa, which can be completely reduced at 150°C for 4 h, meeting the technical requirements of "dense temporary plugging, two-way pressure bearing" to some extent.

Effect of Low-Temperature Plasma-Modified Carbon Fibers on Impact Load Damage of Low-Density Oil-Well Cement

Long-term Thermal Performance of Oil Well Cement Modified by Silica Flour with Different Particle Sizes in HTHP Environment

Study on dynamic mechanical properties and damage characteristics of wollastonite fiber reinforced oil well cement paste

Energy Evolution and Damage Deformation Behavior of Cemented Broken Coal Specimen under Triaxial Compression Condition

The Effect of Polymer Elastic Particles Modified with Nano-Silica on the Mechanical Properties of Oil Well Cement-Based Composite Materials

Preparation of Nano-SiO2/Carbon Fiber-Reinforced Concrete and Its Influence on the Performance of Oil Well Cement

Analysis of impact pressure, rock-breaking effect, and ground vibration induced by the disposable CO 2 fracturing tube

Research on Carbon Dioxide Corrosion of Cement Stones of Oil Well Casings under High Temperature and High Pressure

Deformation and damage of cement sheath in gas storage wells under cyclic loading

Effect of Hole on Oil Well Cement and Failure Mechanism: Application for Oil and Gas Wells

Hybrid Effect of Wollastonite Fiber and Carbon Fiber on the Mechanical Properties of Oil Well Cement Pastes

Effects of porous structure on the deformation failure mechanism of cement sheaths for wellbores

Optimization of degradable temporary plugging material and experimental study on stability of temporary plugging layer

Influences of Fracturing Fluid Injection on Mechanical Integrity of Cement Sheath under Four Failure Modes

The influence of multi-scale tough liquid fiber toughening agent on the mechanical properties of oil well cement-based composite materials

Formation-Damage Mechanism and Gel-Breaker-Free Drill-In Fluid for Carbonate Reservoir

Degradation of chemical and mechanical properties of cements with different formulations in CO2-containing HTHP downhole environment

Experimental and Numerical Simulation Investigation of Cement Sheath Integrity during Multi-Stage Fracturing in Offshore Tight Oil Reservoir

Effects of Carbon Thin Film on Low-Heat Cement Hydration, Temperature and Strength of the Wudongde Dam Concrete

Failure Analysis of Cement Sheath Mechanical Integrity Based on the Statistical Damage Variable

Study on mechanical properties and damage characteristics of cemented waste rock-tailing backfill