Abstract:A new strategy; cation and anion dual gradient, is proposed and successfully constructed at the surface of LiCoO2 to minimize the highly oxidized Co4+ and O− species when charged to high potentials, which not only suppresses the relevant surface side reactions, but also affected the Li+ diffusion kinetics through the induced spinel‐like surface structure, making LiCoO2 exhibit excellent cycling stability and rate capability at the high cutoff voltage of 4.6 V, further validated in the 4.55 V pouch full cell (equivalent to 4.6 V vs Li/Li+).LiCoO2 (LCO) is the most successful cathode material for commercial lithium‐ion batteries. Cycling LCO to high potentials up to 4.5 V or even 4.6 V can significantly elevate the capacity but cause structural degradation due to the serious surface side reaction between the highly oxidized Co4+ and O− species with organic electrolytes. To tackle this concern, a new strategy, constructing cation and anion dual gradients at the surface of LCO (DG‐LCO), is proposed. Specifically, the electrochemically inactive cation and anion are selected to substitute Co3+ and O2− at the surface in a gradated manner, thus minimizing the highly oxidized Co4+ and O− species at high potentials and suppressing the induced surface side reactions. Unexpectedly, this dual gradient design leads to a spinel‐like surface structure coherently with bulk layered structure, which facilitates Li+ diffusion kinetics. Thus, DG‐LCO achieves high capacity and excellent cycling stability at 4.6 V (≈216 mA h g−1 at 0.1 C, a capacity retention of 88.6% after 100 cycles in 1.8 A h pouch full cell at 1 C), as well as improved rate capability (≈140 mA h g−1 at 5 C). These studies provide useful guidelines for future design of cathode materials with long lifespan and high rate capability.

Thermal‐Induced Dopant Precipitation Enabling High‐Quality Surface Modification of LiCoO2

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

High-voltage Performance of LiCoO2 Cathode Studied by Single Particle Microelectrodes –influence of Surface Modification with TiO2

Mitigation of Cation Mixing of LiNiO2-based Cathode Materials by Li-doping for High-Performing Lithium-Ion Battery

Surface Coating with Li-Ti-O to Improve the Electrochemical Performance of Ni-rich Cathode Material

Stabilizing 4.6 V LiCoO2 via Surface‐to‐Bulk Titanium Modification

Enhancing Thermal and High-Voltage Cycling Stability of Ni-Rich Layered Cathodes through a Ti-Doping-Induced Surface-Disordered Structure

Surface modification single crystal Li-rich Li1.2Mn0.54Ni0.13Co0.13O2 as high performance cathode materials for Li-ion batteries

Cathode materials modified by surface coating for lithium ion batteries

A new surface phase of Al2Ti7O15 to enhance the electronic conductivity and interfacial stability of LiCoO2 cathode materials

Ti‐Gradient Doping to Stabilize Layered Surface Structure for High Performance High‐Ni Oxide Cathode of Li‐Ion Battery

An in Situ Formed Surface Coating Layer Enabling LiCoO2 with Stable 4.6 V High‐Voltage Cycle Performances

High‐Entropy Surface Complex Stabilized LiCoO2 Cathode

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

Surface Engineering and Trace Cobalt Doping Suppress Overall Li/Ni Mixing of Li-rich Mn-based Cathode Materials

Nanoscale Manipulation of Spinel Lithium Nickel Manganese Oxide Surface by Multisite Ti Occupation As High‐Performance Cathode

New insights into dry-coating-processed surface engineering enabling structurally and thermally stable high-performance Ni-rich cathode materials for lithium ion batteries

Feasibility to Improve the Stability of Lithium-Rich Layered Oxides by Surface Doping

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

Surface modification of Li-rich layered Li1.2Mn0.54Ni0.13Co0.13O2 oxide with Fe2O3 as cathode material for Li-ion batteries

Improving diffusion kinetics and phase stability of LiCoO2 via surface modification at elevated voltage