Abstract:This study achieves combustion applications of methanol-diesel dual-direct injection in a retrofitted diesel engine by investigating methanol sprays and engine performance/emissions. Methanol draws high attention due to its green production potential and ease of adaptation to existing combustors and supply infrastructure. One of the most promising methods for utilising methanol in diesel engines is the dual direct injection, which provides a wide operating range and flexible injection control. This study provides an effective solution for dual direct injection by implementing a nozzle cap idea, which can mount a conventional direct injector for methanol delivery in an existing diesel engine. The custom-made nozzle cap can provide hole orientation variations, which effectively controls the methanol-air mixture distributions within the piston bowl. To this end, methanol sprays formed through the three-hole nozzle cap are analysed for varied injector pressure of 15 ∼ 35 MPa. High-speed schlieren imaging confirmed working of the new nozzle for methanol injection with expected results of increased liquid penetration length and cone angle for higher injection pressure. The spray images also helped understand how the mixtures would be distributed within the piston bowl due to direct injection. Experiments performed on a 1-litre single-cylinder common-rail diesel engine operating at 1400 rpm, up to 70 % methanol energy fraction and a broad range of methanol injection timings of BDC to TDC, showed that the methanol-diesel dual direct injection combustion produces overall lower power output than the diesel baseline due to lower calorific value and flame temperature of methanol but significantly reduced CO 2 emissions by up to 16 % and very low smoke emissions. The results showed high sensitivity to methanol injection timings and energy fraction in terms of the measured pressure, derived heat release rate and produced power due to an increase in mixture homogeneity for earlier injection timings and stratified charge conditions for later injection timings. However, the nozzle orientation change and expected methanol-air mixture distributions showed no measurable impact on pressure and heat release rate as well as engine power output and combustion stability. The most significant impact of the methanol three-hole nozzle orientation and resulting mixture distributions was found from uHC and NO x emissions because a nozzle orientation directing methanol more towards the corner of the piston bowl opposite side of the injector led to increased liquid wall wetting and methanol in crevice volumes and thereby causing less complete combustion for higher uHC and lower NO x . The low sensitivity of methanol mixture distributions to the in-cylinder pressure and engine power output but the measurable impact found on uHC and NO x emissions empathies the required optimisation of methanol direct injector nozzle depending on the combustion chamber design of the base diesel engine.

Combustion characteristics of methanol engine applying TJI-HPDI with optimized pre-chamber nozzle structure under different injection and spark strategy

Effects of Injection Parameters and EHN Mixing on the Combustion Characteristics of Fueling Pure Methanol in a Compression Ignition Engine

Parametric Study on the Methanol/diesel JCCI Mode with Dual-Direct Injection System in a Light-Duty Engine

Fundamental Experiment of Ignition and Flame Development in Turbulent Jet Ignition Ignited Methane Jet Flame

Numerical Investigation on the Influence of Injection Location and Injection Strategy on a High-Pressure Direct Injection Diesel/Methanol Dual-Fuel Engine

Combustion Characteristics of High Pressure Direct-Injected Methanol Ignited by Diesel in a Constant Volume Combustion Chamber

Investigation on a High-Stratified Direct Injection Spark Ignition (DISI) Engine Fueled with Methanol under a High Compression Ratio

Experimental Investigation on the Effects of Direct Injection Timing on the Combustion, Performance and Emission Characteristics of Methanol/Gasoline Dual-Fuel Spark Turbocharged Ignition (DFSI) Engine with Different Injection Pressures under High Load

Investigation on mixture formation and combustion characteristics of a heavy-duty SI methanol engine

Assessment of the Effects of Intake Temperature and Injector Structure on the Combustion Characteristics of Direct‐Injection Spark‐Ignition Methanol Engines

Research on the structure of pre-chamber and jet orifice of a turbulent jet ignition rotary engine fueled with methanol/gasoline blends

Visualization Study on Combustion Characteristics of Direct-Injected Hydrous Methanol Ignited by Diesel in a Constant Volume Combustion Chamber

Optical Diagnostics of Methanol Active-Thermal Atmosphere Combustion in Compression Ignition Engine

Experimental Study on the Stratified and Homogeneous Charge of a Direct-Injection Spark Ignition Methanol Engine

Improving the lean burn performance of a high compression ratio methanol engine by multiple-injection

Effects of injection and spark timings on combustion, performance and emissions (regulated and unregulated) characteristics in a direct injection methanol engine

Experimental Observation of the TJI-initiated HPDI Gas Combustion: Vertically Crossed Flame Jet and Methane Jet

Experimental Study of the Ignition Chamber with Accelerating Cavity Applying to Methanol Lean Combustion

Effect of multi-injection strategy on characteristics of methanol-fueled direct injection spark ignition engine

Effects of Pilot Injection Strategy of Diesel Fuel on Combustion Characteristics in a Premixed Methanol-Air Mixture Atmosphere in a CVCC

Effect of three-hole nozzle orientations on sprays and combustion in methanol-diesel dual direct injection engines