Abstract:Summary form only given. Two very different approaches to theoretical description of interaction of high-pressure arc plasmas with refractory cathodes exist in the literature. One group of researchers believes that space-charge effects on refractory cathodes are small and contribute to the arc voltage no more than one or two volts. Accordingly, these researchers use simulation models which are based on the assumption of quasi-neutrality, or even stronger assumption of local thermodynamic equilibrium (LTE), in the whole arc volume. Other researchers believe that the voltage drop in the near-cathode space-charge sheath is no less than 10V and rely on models where the near-cathode sheath plays a central role.Extensive experimental data on near-cathode voltage obtained during the last decade for low-current arcs (I ≤ 10A), which are in the range 10-50V, indicate that the first abovedescribed (no-sheath) approach is not justified and the second (sheath-accounted) approach should be used for such arcs, and this is a common knowledge now. Unfortunately, reliable experimental data are difficult to obtain for high-current arcs. The status quo is as follows: the sheath-accounted approach is used in virtually all works on modelling of low-current arcs; the no-sheath approach is used in most works on highcurrent arcs. Amazingly, there has been little interaction between research in these two fields, in spite of the physics of near-cathode plasma layers in highand low-current arcs being similar, and the question as to what physical reasons could justify the use of so strongly different approaches has not even been asked. In this work, both a sheath-accounted model and an LTE model are used for modelling of electrical characteristics of a short atmospheric-pressure argon arc. It is found that the LTE model substantially overestimates the resistance of the part of the arc column adjacent to the cathode sheath. Furthermore, it is shown that if this resistance is evaluated - n the framework of the LTE model in an accurate way, than the calculated arc voltages are significantly higher than those observed in the experiment. However, conventional numerical algorithms like SIMPLE perform this evaluation in an inaccurate way and the use of these algorithms amounts to a cut-off, which is why it is possible to obtain in the modelling arc voltages comparable to the experimental values.

Different modes of arc attachment at HID cathodes: simulation and comparison with measurements

Current–voltage Characteristics of Hydrogen DC Plasma Torches with Different Sizes in an External Axial Magnetic Field

Validated two-dimensional modeling of short carbon arcs: Anode and cathode spots

Chemical Non-equilibrium Simulation of Anode Attachment of an Argon Transferred Arc

Effect Of A Near-Cathode Sheath On Heat Transfer In High-Pressure Arc Plasmas

Effect of Cathode-Plasma Coupling on Plasma Torch Operation Predicted by a 3D Two-Temperature Electric Arc Model

Simulation Results of Arc Behavior in Different Plasma Spray Torches

Particle-in-cell and Monte Carlo Collision Simulations of the Cathode Sheath in an Atmospheric Direct-Current Arc Discharge

Sheath Vs. Quasi-Neutral Plasma Voltages in High-Pressure Arc Discharges

Investigation of a short argon arc with hot anode. Part I: numerical simulations of non-equilibrium effects in the near-electrode regions

Stationary Carbon Cathodic Arc: Plasma and Film Characterization

Two-temperature modeling of lamellar cathode arc

Two-dimensional Modeling Concerning the Effects of the Boundary Conditions along the Cathode Sheath-arc Column Interface on the Characteristics of the Dual-jet Arc Plasmas

Two-dimensional self-consistent numerical simulation of the whole discharge region in an atmospheric argon arc

Numerical study of the power deposition in low-pressure hollow cathode arc discharges

Non-equilibrium Modelling of Free-Burning Argon Arc in Different Anode Sheath Regimes

Numerical investigation of regimes of current transfer to anodes of high-pressure arc discharges

Hollow cathode modeling: II. Physical analysis and parametric study

2D Self-Consistent Modeling of Arc–electrode Interaction in GTAW Using a Finite Volume Method

Three-dimensional, Nonequilibrium Effects in a High-Intensity Blown Arc

Hollow cathode modeling: I. A coupled plasma thermal two-dimensional model